The contact owns a 2003 Mercury Sable. The contact stated while driving at an undisclosed speed, the vehicle lost motive power. The vehicle coasted to the side of the road and was towed to the residence. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The manufacturer was not made aware of the failure. The failure mileage was approximately 83,000.
The worst 2003 Mercury Sable problems
Ranked by number of owner complaints. Mileage and cost come from what owners wrote.
Problems by type
Tap a problem to see which part fails, at what mileage and in which other years.
- Suspension47
- Transmission30
- Acceleration28
- Engine27
- Body20
- Visibility19
- Brakes14
- Lights13
- Electrical10
- Airbags8
- Fuel system7
- Seat belts5
- Steering3
- Locks2
- Wheels2
- Driver assistance1
- Tires1
Specific symptoms reported on the 2003 Mercury Sable
Coil spring 41Water leak 15Tire blowout 11Transmission failure 10No deployment 7Adaptive cruise 6Grinding brakes 6
Recalls 3
Engine and engine cooling
- What is wrong
- On certain vehicles, the air filter paper in these vehicles can smolder or burn.
- Risk
- This can lead to damage to the air induction system on these vehicles and/or an underhood fire.
- Remedy
- Dealers will replace the air filter element. Owner notification began on march 10, 2004. Owners should contact ford at 1‑800‑392‑3673.
Recall number 04V105000 · Recall details
Exterior lighting: brake lights: switch
- What is wrong
- Certain passenger vehicles are being recalled to correct a problem with a malfunctioning stop lamp switch and/or associated wiring. This malfunctioning could render the stop lamps inoperable or cause them to stay on all the time. This could cause confusion to a following driver, which could lead to a crash.
- Risk
- In addition, if the switch and/or associated wiring fail in the open position, the brake lights will not actuate and the driver will not be able to shift the vehicle out of "park" if they fail in the closed position, the brake lights will remain on, which will not allow the speed control to be activated. This could also cause the battery to discharge.
- Remedy
- Dealers will remove the stop lamp switch and associated wiring assembly and install a newly designed stop lamp switch and wire assembly. Owner notification is expected to begin on april 5, 2004. Owners should contact ford at 1‑800‑392‑3673.
Recall number 04V106000 · Recall details
Visibility: windshield
- What is wrong
- Certain passenger vehicles fail to comply with the requirements of federal motor vehicle safety standard no. 212, "windshield mounting." the windshields may potentially exhibit increased wind noise, water leakage, and squeaks and rattles.
- Risk
- Potential loss of windshield retention may also reduce occupant protection in the event of a crash.
- Remedy
- Dealers will replace these windshields. Owner notification began on march 31, 2003. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact ford/mercury at 1‑800‑392‑3673.
Recall number 03V087000 · Recall details
See all 3 recalls for the 2003 Mercury Sable
Defect investigations
Speed control cable damage
On June 21, 2013, Ford initiated Customer Satisfaction Program 13B04 to address a concern with Speed Control Cable damage in certain model year (MY) 2000 through 2003 Taurus and Sable vehicles equipped with 3.0L 4V Duratec engines and built at the Chicago assembly plant.In the dealer letter for the program, Ford indicates that the Speed Control Cables on affected vehicles may be susceptible to damage or becoming partially disconnected during under hood vehicle maintenance (e.g., replacing a battery or changing the air filter) and that a damaged Speed Control Cable could interfere with the throttle's full return to idle when the accelerator pedal is released.Ford's program instructs dealers to inspect the Speed Control Cables and replace any with any portion of either collar retention tab missing.Dealers will install a Collar Reinforcement Clip at the Speed Control Cable collar in all vehicles. Figure 1 shows the location of the Speed Control Cable in the engine compartment and the proximity of the battery and air filter.The failure mode of the cable assembly is associated with the plastic collar used to secure the cable to a bracket near the throttle body (Figure 2).Damage to one or both retention tabs used to secure the cable ferrule within the collar may allow the ferrule to become disconnected from the collar when the throttle is opened during accelerator pedal application.Additional examples of Speed Control Cables with damaged collar retention tabs and partial ferrule displacement are shown in Figures 3 through 5.If the displacement pulls the ferrule completely out of the collar, the ferrule end may contact the face of the collar when the accelerator pedal is released and the throttle is returning to idle (Figure 6).This results in a throttle stuck at approximately 26-29% open.Testing conducted at the federal safety agency's Vehicle Research and Test Center found that brake booster vacuum may become depleted, resulting in reduced brake effectiveness, if the brake is applied repeatedly when the throttle is stuck at this position.Drivers who experienced this condition have reported being surprised that the engine speed did not drop as expected and in some cases misjudged the degree of braking required to slow the vehicle.Some drivers reported difficulty in braking the vehicle and responded by shifting to neutral or turning the engine off.One minor crash occurred when the vehicle contacted a roadside fence post after the driver responded to the stuck throttle by shifting the car to neutral, turning the engine off and coasting to the side of a roadway with no shoulder, resulting in approximately $400 damage to the vehicle.There were four crashes reported which were attributed to increased stopping distance caused by the increased engine power and/or reduced brake effectiveness, including two of the complaints to ODI.In one crash reported to ODI (VOQ 10516101), the subject vehicle allegedly hit the back end of a truck at approximately 40 mph causing about $2000 damage.In the other crash complaint to ODI (VOQ 10501834), the subject vehicle side-swiped a vehicle as the driver was unable to stop in time and attempted to maneuver around a line of vehicles stopped at a traffic light.When the tow truck driver subsequently started the incident vehicle, the engine was still racing and it was verified that the Speed Control Cable ferrule was stuck on the collar.After further investigation, ODI does not consider the crashes reported in VOQs 10456249 and 10159399 to be related to the Speed Control Cable problem.
PE12033
Front Suspension Coil Spring Fracture
To date, ODI is aware of 2,401 non-duplicative complaints related to the alleged defect. In addition, ODI is aware of 1,411 subject vehicles with one or more warranty claims related to the alleged defect. In total, ODI is aware of 3,645 unique subject vehicles that have experienced one or more front suspension coil spring fractures. ODI is also aware of four minor crashes related to the alleged defect resulting in one minor injury.With greater than eight years of exposure, a large subject vehicle population and approximately 2,052 reported front tire punctures caused by fractured coil springs (at all speeds), there have been no reported severe crashes, deaths or injuries related to the alleged defect. The real world consequences of these defective coil springs have been a small number of minor control problems that resulted in minor damage; suggesting that the effect of the defect on vehicle control is minor.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted. Accordingly, this investigation is closed. The closing of this investigation does not constitute a finding by the federal safety agency that a safety-related defect does not exist. The agency will continue to monitor this issue and will take further action if warranted by the circumstances. See the EA08-018 Engineering Analysis Closing Report for more details.
EA08018
Engine stalling ffv
On october 11, 2006, public citizen petitioned odi to investigate reports of engine stalls caused by e85 fuel in certain model year (my) 2003 - 2005 ford taurus flex-fuel vehicles (ffv). Odi's review of the petition and other available data found a low stall rate attributable to e-85 fueling and that the main concerns,prolonged engine start and rough idle during cold engine startup at winter temperatures, were resolved by an engine software update.to ensure that all subject vehicles receive this update, ford initiated a notification campaign to offer free engine computer recalibration.based on this information, this defect petition is denied. This denial should not be construed as a finding that no safety defect exists.odi reserves the right to reconsider this issue if future data warrant.additional details can be found in the federal register notice posted in the dp06-005 public file.
DP06005
Brake light switch failure
Ford conducted a recall in march, 2001 to correct a defect affecting the brake light switch in my 2000 through early-2001 taurus and sable vehicles equipped with power adjustable pedals (recall 01v‑078).rq03-008 was opened to investigate complaints concerning the remedy and scope of 01v‑078.odi's analysis identified concerns with post-repair failures in recalled vehicles,failures in my 2001-02 vehicles with adjustable pedals that were not included in recall 01v‑078, and failures in my 2000 vehicles with fixed pedals.(note: the manufacturer failure data in this resume includes all crashes and injuries, but the complaint information is limited to my 2001-02 vehicles that were not included in the scope of recall 01v‑078.)on march 1, 2004, ford notified the federal safety agency of a safety defect in my 2000 through early-2003 taurus and sable vehicles equipped with adjustable pedals and my 2000 subject vehicles equipped with fixed pedals (recall 04v‑106).the notification identified three factors contributing to brake light circuit failures:(1) continuing grease contamination issues that prompted 01v‑078; (2) misalignment of the booster rod pin and the brake light switch; and (3) wire assembly fatigue.the first two conditions were limited to vehicles with adjustable pedals and the latter condition affected vehicles with fixed pedals.ford will instruct owners to bring their vehicles to a dealer to have the brake light switch and associated wiring replaced with a re-designed brake light switch and wiring assembly.
RQ03008
Technical service bulletins for the 2003 Mercury Sable 66
Bulletins tell dealers how to fix known problems. A warranty extension means the manufacturer pays for that repair for longer.
- This article supersedes TSB 19-2026 to update the vehicle model years affected
- Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit...
- Ford: speed control cable is susceptible to damage and CAN disconnect during hood maintenance and also...
- Camshaft tick noise - 3.0L 4V engine only. tt
- Power lock concerns - service tip. tt
- Power window concerns - service tip. tt
- Buck/jerk and miss during drive cycle above 3000 RPM - no DTC - 3.0L 2V gas and ffv engine. tt
- Erratic fluid level reading on transaxle DIPSTICK-LEAKS-4F50N, AX4N, AX4S transaxle. sc
- Malfunction indicator lamp coming on with diagnostic trouble codes (dtcs) P0171, P0172, P0174 and/or P0175...
- Safety belt retraction speed. tt
2003 Mercury Sable fuel economy
Official EPA estimates in miles per gallon (MPGe for electric). Ranges cover trims that share the same engine.
| Engine | Drive | City | Highway | Combined |
|---|---|---|---|---|
| 3.0L 6‑cyl | FWD | 17-18 | 24-26 | 19-21 |
What 2003 Mercury Sable owners say
Most recent owner complaints, unedited.
Tl* the contact owns a 2003 mercury sable. The contact stated while driving 30 MPH, the vehicle decelerated independently. The contact stated no warning light was illuminated. The contact parked on the side of the road. The vehicle was not drivable. The vehicle was towed to an independent mechanic and the contact was informed that the transmission needed to be replaced. The vehicle was not diagnosed nor repaired. A dealer was not contacted. The manufacturer had been informed of the failure. The failure mileage was approximately 30,000.
Idriving under normal conditions on a city street in 2003 merc sable with 33k miles. While in motion, the transmission fails with no forward or reverse working or any other mechanical warnings.( no transmission codes on obdii. I was immediately able to coast into a drugstore parking lot. Car towed to local ford dealer. Dealer informed that the torque converter splines have failed and torque converter needs to replaced for $ 1726.00. Dealer repaired vehicle, replaced with ford re-manuafactured torque converter. Searched intern net and found same numerous complaints of ford torque converters spline failures. Based on the type and number of complaints this appears to warrant an audit of this safety problem. There are other reported complaints that vehicles were traveling on highways and suffered transmission failures while in motion without any warnings.
So sorry to bother you. I have a mercury sable 03 which has been accelerating by itself because the throttle cable gets stuck. I saw an article that said my year taurus and sable have this problem as well as saw that all those in the junk yard have the exact same problem. In the article it said ford agreed to fix those to stop further investigation. How would I go about getting this fixed? Please and thank you. My vehicle started going 79 and wouldn't stop. Even in neutral it went 4000 RPM until the throttle cable was unjammed. And continues to do so
I was driving my car on a city street and the car started accelerating on its own and I tried to brake but my brakes would not work. I had to put both feet on the break to slam hard enough to try to get it to slow down even a little. I found out that the throttle cable got stuck and could not go back in causing the car to keep accelerating.
2003 mercury sable. Consumer writes in regards to being charged for vehicle repairs that were under warranty. *ld
Why was I charged $249.90 labor charges when the vehicle was only in my hands for a couple of days after being purchased from king buick but not for parts, shop materials and use of a loaner car. I should have paid nothing under a warranty and would like to know if ford has responsibility for that. Please feel free to call my call on [xxx](c) or [xxx](h) if you need more information about this. I was right across the street from the community where I reside and drove the car to king buick gmc immediately. Information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(b)(6).
1. The hood closes apparently fine, it does not open if I try to, however keeps opening every 20 minutes after driving. I could not find the cause. 2. Very strong smell of gas keeps ocurring, no signs or drops or viisual leak puddle.
Tl* the contact owns a 2003 mercury sable. While the vehicle was operated, it lost engine power without warning. The vehicle was towed to dom's getty service station (308 mercer st, hightstown, nj) where it was diagnosed as a transmission failure. The dealer was not contacted. The manufacturer was contacted and offered no assistance. The failure mileage was approximately 57,000.
Tl* the contact owns a 2003 mercury sable. The contact stated that the transmission failed. While driving approximately 60 MPH, the vehicle lost acceleration. The vehicle was towed to dom's getty station (heightstown, nj 08520, phone (609) 448-4146) for diagnostic testing, which located the failure at the transmission input shaft and torque converter. The vehicle was not repaired. The manufacturer was notified. The failure mileage was 57,000.
Compare the 2003 Mercury Sable
Other model years
1990199119921993199419951996199719981999200020012002200320042005200620082009
Questions about the 2003 Mercury Sable
Is the 2003 Mercury Sable reliable?
Owners have filed 201 complaints about the 2003 Mercury Sable, 2.4 times a typical Sable model year. It is one of the years we flag to avoid.
What is the 2003 Mercury Sable year score?
The 2003 Mercury Sable scores 42 out of 100 (below average). The score compares it with the other model years of the Mercury Sable: 75 is a typical year, 50 means twice the usual complaints, and serious complaints and recalls lower it.
What is the most common problem with the 2003 Mercury Sable?
Suspension, with 47 complaints, typically around 75,000 miles. Next is transmission (30).
How many recalls does the 2003 Mercury Sable have?
3 recalls, covering engine and engine cooling, exterior lighting and visibility.
What gas mileage does the 2003 Mercury Sable get?
Official estimates for the 2003 Mercury Sable range from 19 to 21 mpg combined. The most efficient version (3.0L 6-cyl, FWD) gets 17-18 city and 24-26 highway.
VIN decoder
See the problems and recalls for an exact car
Buying a used 2003 Mercury Sable?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history