Peterbilt 387 recalls

What is wrong

PACCAR Incorporated (PACCAR) is recalling certain 2008-2019 Peterbilt 330, 335, 337, 340, 348, 365, 367, 384, 386, 387, 388, 389, 567, 579 and 587 vehicles and 2008-2020 Kenworth T170, T270, T370, T660, T680, T800, T880, and W900 vehicles equipped with NAMUX Software. In the event that the Anti-lock Brake System (ABS) loses battery and/or ignition power to the controller, the dash warning light for the ABS may not illuminate to warn the driver of the loss of ABS. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 121, "Air Brake Systems," and 136, "Electronic Stability Control System on Heavy Vehicles."

Risk

If the driver unknowingly operates the vehicle without the ABS functioning, there would be an increased risk of a crash.

Remedy

PACCAR will notify owners, and dealers will update the NAMUX software within the cab control module, free of charge. PACCAR issued owners an interim notification on June 4, 2020. The recall began May 26, 2020. Owners may contact Kenworth customer service at 1‑425‑828‑5888 or Peterbilt customer service at 1‑940‑591‑4220. PACCAR's number for this recall is 20pbc AND 20KWB.

Recall number 20V199000 · Recall details

What is wrong

PACCAR Incorporated (PACCAR) is recalling certain model year 2006-2016 Peterbilt 587, 579, 567, 389, 388, 387, 385, 382, 379, 378, 367, 365 and 357 trucks manufactured July 25, 2005, to February 26, 2016. The affected vehicles may be equipped with Tire and Rim Certification Labels that list a tire pressure below the actual correct amount. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard No. 120, "Tire selection and rims and motor home/recreation vehicle trailer load carrying capacity information for motor vehicles with a GVWR of more than 4,536 kilograms (10,000 pounds)."

Risk

If the tires are underinflated due to the incorrect inflation pressure listed on the label, the truck may not be able to carry the maximum gross vehicle weight rating (GVWR) load listed without experiencing tire failure which would increase the risk of a crash.

Remedy

Peterbilt will notify owners and mail them a corrected Tire and Rim certification label, free of charge. The recall began on June 19, 2015. Owners may contact Peterbilt customer service at 1‑940‑591‑4000. PACCAR's number for this recall is 215-D.

Recall number 15V132000 · Recall details

What is wrong

Paccar is recalling certain model year 2011-2012 kenworth t660, t700, and t800 vehicles manufactured from april 19, 2010, through may 13, 2011, and model year 2008, 2010, and 2011 peterbilt 365, 367, 384, 386, 387, 388 and 587 vehicles manufactured from april 20, 2010, through june 11, 2011, and equipped with paccar mx engines and eaton ultrashift dm or allison automatic transmissions (without auto-neutral). The fast idle control may be activated by the operator while the transmission is in gear.

Risk

If the fast idle control function is engaged with the transmission in gear, the vehicle could unexpectedly accelerate and override the parking brake and , creating a risk of a crash and damage to other vehicles or property and the potential for injury to nearby pedestrians.

Remedy

Kenworth and peterbilt dealers will update the engine software for the affected chassis. This service will be performed free of charge. The safety recall began on august 22, 2011. Owners may contact kenworth at 1‑425‑828‑5440 and peterbilt at 1‑940‑591‑4196.

Recall number 11V380000 · Recall details

What is wrong

Paccar is recalling certain model year 2007-2011 kenworth c500, t2000, t600, and t660, as well as model year 2009-2011 peterbilt 387 and 388 trucks equipped with caterpillar c15 engine and manufactured from may 11, 2006, through september 17, 2010. Degradation of a combustion tube weld can cause radial heat impingement on the body which may burn through certain bodies used on c15 engines.

Risk

This could result in a fire.

Remedy

Caterpillar is handling the owner notification and remedy for this campaign. Please see caterpillar's defect report 11e-006. Caterpillar will replace the single piece combustion tube with a thick wall combustion tube which will not allow the heat to break through. This service will be performed free of charge. Due to a parts supply issue, owners will be notified by the end of april 2011 about the safety defect, and will then be notified again once the free remedy is available, currently estimated to be around late july 2011. Owners may contact caterpillar toll-free at 1‑800‑447‑4986.

Recall number 11V203000 · Recall details

What is wrong

Paccar is recalling certain model year 2008-2012 kenworth t2000, t660, t700, t800, and w900, as well as model year 2009-2012 peterbilt 365, 367, 384, 386, 387, 388, 389, and 587 trucks equipped with paccar mx engines. The oil module centrifugal spinner filter cap in the paccar mx engine may become loose, possibly allowing the cap to come off and engine oil to partially discharge from the oil module onto exhaust components.

Risk

The discharge of engine oil onto exhaust components which are hot, such as when the engine is under significant load, may cause a fire.

Remedy

Dealers will re-torque the oil module filter cap and install a secondary retention device on the secondary centrifugal spinner filter cap. This service will be performed free of charge. The safety recall is expected to begin during march 2011. Owners may contact kenworth at 1‑425‑828‑5440 and peterbilt at 1‑940‑591‑4196.

Recall number 11V127000 · Recall details

What is wrong

Paccar is recalling certain model year 2007-2008 kenworth and peterbilt vehicles manufactured from february 2, 2006 through april 30, 2007. The bearing surfaces of the extended lube universal joint that attaches the inter-axle driveline to the drive axle may become prematurely worn due to breakdown of lubrication and/or excessive heat. Prematurely worn bearing surfaces may result in the u-joint becoming loose and/or binding. This condition may result in universal joint failure, allowing the inter-axle driveline to detach from the axle.

Risk

Detachment of the driveline from the axle may cause the vehicle to lose power and become disabled in the roadway. Also, the driveline could drop from the vehicle into the roadway increasing the risk of a crash.

Remedy

Paccar is working with its supplier to remedy the vehicles free of charge. The safety recall is expected to begin during february 2011. Owners may contact kenworth at 425‑828‑5440 and peterbilt at 940‑591‑4196.

Recall number 10V634000 · Recall details

What is wrong

Paccar is recalling certain model year kenworth and peterbilt vehicles. A manufacturing defect in the seal supplied by a component manufacturer installed on the output shaft of the exhaust gas recirculation (egr) valve actuator may cause eventual delamination of the seal. Delamination of the seal may allow engine oil to leak from the egr valve onto exhaust components.

Risk

The leaking of engine oil onto hot exhaust components, such as when the engine is under significant load, may create the possibility of a fire.

Remedy

Dealers will replace the egr valve assembly on the subject vehicles equipped with the paccar mx engine. This service will be performed free of charge. The safety recall began on october 29, 2010. Owners may contact kenworth at 425‑828‑5440 and peterbilt at 940‑591‑4196.

Recall number 10V453000 · Recall details

What is wrong

Paccar is recalling certain model year 2008-2010 trucks equipped with trw steering shafts. The circumferential weld around the steering shaft tube that welds the splined tube to the non-splined tube may be mislocated. Mislocation of the circumferential weld may allow the splined tube and non-splined tube to rotate relative to one another during a low speed, high torque turn, possibly resulting in a separation of the two tubes.

Risk

A separation of the splined and non-splined tubes would cause a loss of steering control and increase the risk of a vehicle crash.

Remedy

Dealers will inspect the steering shaft using a weld placement gauge provided by trw. Any steering shaft found to have been welded improperly will be replaced free of charge. The safety recall began on july 30, 2010. Owners may contact kenworth at 425‑828‑5440 and peterbilt at 940‑591‑4196.

Recall number 10V308000 · Recall details

What is wrong

Paccar is recalling 2,096 my 2009 kenworth and peterbilt vehicles equipped with trw steering shafts. Mislocation of a circumferential weld may allow the splined tube and non-splined tube to rotate relative to one another during a low speed, high torque turn, possibly resulting in a separation of the two tubes.

Risk

A separation of the splined and non-splined tubes could cause a loss of steering control and increase the risk of a crash.

Remedy

Dealers will inspect the steering shaft using a weld placement gauge and miswelded steering shaft will be replaced free of charge. The recall began july 31, 2009. Owners may contact kenworth at 1‑425‑828‑5440 and peterbilt at 1‑940‑591‑4196.

Recall number 09V258000 · Recall details

What is wrong

Paccar is recalling 1098 kenworth my 2008 t800, w900, my 2008-2009 t2000 and peterbilt my 2007-2009 379 and 387 trucks equipped with c15 caterpillar diesel engines. The aftertreatment regeneration device (ard) may develop a hole and heat and flame may escape during a regeneration of the diesel particulate filter.

Risk

This may result in a fire hazard.

Remedy

Paccar is working with caterpillar and will inspect and remedy the engines free of charge. Owners may contact caterpillar at 1‑800‑447‑4986, kenworth at 425‑828‑5440 or peterbilt at 940‑591‑4196.

Recall number 09V019000 · Recall details

What is wrong

Paccar is recalling 4,883 my 2006-2009 kenworth t600, t660, t800, w900, t2000 and my 2008-2009 peterbilt 365, 367, 379, 384, 386, 387, 388 and 389 trucks. Inadequate stiffness of the diesel particulate filter (dpf) bracket could result in separation of the dpf from the chassis.

Risk

A vehicle crash could occur if another vehicle strikes the dpf on the roadway.

Remedy

Paccar is working with caterpillar to repair these vehicles (please see 08e041). Owners may contact caterpillar at 1‑800‑447‑4986 or kenworth at 1‑425‑828‑5440 or peterbilt at 1‑940‑591‑4196.

Recall number 08V487000 · Recall details

What is wrong

Paccar is recalling 6,169 my 2008 kenworth t300, t660, t800, t2000, w900 and c500 vehicles and my 2008-2009 peterbilt models 365, 367, 384, 387, 388, 389 and 389 kits. Certain door latch assemblies on these vehicles fail to conform to the requirements of federal motor vehicle safety standard no. 206, 'door locks and door retention components." the rotor in some of these door latch assemblies did not receive the proper heat treatment and may be soft.

Risk

In the event of a crash, force could cause the rotor to crack and the door would not have primary or secondary closing security which could possibly lead to injury of the vehicle occupant.

Remedy

Paccar is working with trimark and will inspect and replace the door latch if it is found to be defective. The recall began on march 14, 2008. Owners may contact kenworth at 1‑425‑828‑5440 or peterbilt at 1‑940‑591‑4196.

Recall number 08V065000 · Recall details

What is wrong

Certain trucks equipped with eaton synflex eclipse brand extruded nylon air brake hose tubing fail to comply with the requirements of federal motor vehicle safety standard no. 106, "brake hoses." the tubing was manufactured with only four layers of nylon material, instead of the specified five layers.

Risk

The diameter of the hose affects the fittings which may allow air to leak from the brakes and create the potential for a vehicle crash.

Remedy

Dealers will inspect the air brake hoses and, if necessary, replace the hoses. The recall began on february 22, 2008. Owner notification schedule for this campaign. Owners may contact kenworth at 1‑425‑828‑5440 or peterbilt at 1‑940‑591‑4196.

Recall number 08V002000 · Recall details

What is wrong

On certain kenworth and peterbilt heavy duty trucks equipped with tas-85 trw steering gears, the inner surface of the outer sector shaft teeth of the steering gears may have an incorrect involute profile, which may lead to chipping and damage of the gearing system.

Risk

This type of damage may cause a "bind/stick" condition in the vehicle steering during a turn increasing the risk of a crash.

Remedy

Dealers will repair and replace any suspect tas-85 steering gear assembly free of charge. The recall began on january 9, 2008. Owners may contact kenworth at 425‑828‑5440 and peterbilt at 940‑591‑4201.

Recall number 07V591000 · Recall details

What is wrong

On certain peterbilt trucks, the longitudinal seams on the fuel tanks were fabricated using an incorrect weld speed for the given material thickness. This error resulted in a weld which did not completely penetrate the entire material thickness.

Risk

Fuel tanks possessing this defect could leak diesel fuel in the event of a crash.

Remedy

Dealers will inspect and replace any defective fuel tanks free of charge. The recall began on october 8, 2007. Owners may contact peterbilt at 940‑591‑4201.

Recall number 07V409000 · Recall details

What is wrong

On certain trucks, the axle housings may have been manufactured with steel that was out of specification which could result in a fatigue failure over time.

Risk

If a fatigue failure occurs and is left unattended, the axle may lock up or the end of the axle could come off, which may result in a vehicle crash.

Remedy

Dealers will inspect and replace the axles free of charge. The recall began on may 9, 2007. Owners may contact kenworth at 425‑828‑5440 and peterbilt at 1‑940‑591‑4196.

Recall number 07V132000 · Recall details

What is wrong

On certain trucks, the fifth wheel king pin release air valve internal spool was installed backwards. The air option of the king pin release system would be inoperable. To correct this situation in production, the vehicle's air lines were mistakenly reversed rather than replacing the valve.

Risk

There is a possibility that the king pin can release without the driver's knowledge. When this occurs, the driver could drive away and the trailer could become disengaged.

Remedy

Dealers will inspect the functionality of the king pin release system and suspect valve. If any vehicles have a non-conforming valve or incorrect plumbing, it will be replaced and re-plumbed. The recall began on february 28, 2007. Owners may contact peterbilt at 940‑591‑4196.

Recall number 07V033000 · Recall details

What is wrong

On some peterbilt trucks, certain parts used in the air suspensions have a high copper content causing premature failure.

Risk

Failure could cause erratic vehicle handling which can cause a vehicle crash without warning.

Remedy

Dealers will inspect and, when necessary, replace the defective parts. The recall began on january 17, 2007. Owners may contact peterbilt at 1‑940‑591‑4196.

Recall number 06V490000 · Recall details

What is wrong

On certain trucks, when using a cummins electronic icon service tool 2.2, an unintended engine start will occur.

Risk

Given the purpose and functionality of this service tool, this series of events would only occur in a service facility and could pose a hazard if the truck were to unexpectedly move or the engine to start without any warning, possibly causing personal injury.

Remedy

Cummins is conducting this recall (please see 06e063000) and will replace the icon service tool 2.2 with a new icon service tool 2.3 free of charge. Owners may contact cummins at 1‑800‑343‑7357 or peterbilt at 1‑940‑591‑4201.

Recall number 06V251000 · Recall details

What is wrong

On certain tractors equipped with caterpillar diesel engines, the variable valve actuation oil line may wear against the sharp edge of the cylinder head if not positioned correctly.

Risk

The oil line may be cut on the cylinder head causing an oil leak and a possible fire.

Remedy

Caterpillar, in conjunction with paccar, will be conducting the owner notification and remedy for this campaign free of charge. Owners may call caterpillar at 309‑675‑6496, kenworth at 425‑828‑5440, or peterbilt at 940‑591‑4201.

Recall number 05V570000 · Recall details

What is wrong

On certain trucks equipped with the bendix electronic stability control (esp) system, the system uses multiple sensors and an electronic control unit (ecu) to control vehicle under steer, over-steer, and rollover situations. The system relies on vehicle sensors to be functioning and aligned properly. The steering angle sensor has the potential to be misaligned with the steering column shaft, thereby providing incorrect information to the bendix ecu.

Risk

This condition could affect vehicle throttle control and braking, thereby leading to loss of vehicle steering control which could cause a crash without warning.

Remedy

Because of the immediate and substantial risk, kenworth and peterbilt dealers will first deactivate the yaw control feature of the bendix esp system preventing inadvertent esp activation. When parts are available, the steering column will be replaced to insure proper alignment of the steering shaft sensor and the full esp system will be reactivated. The recall began on december 7, 2005. Parts to complete the remedy are estimated to be available in early 2006. Owners may contact kenworth at 1‑425‑828‑5440 or peterbilt at 1‑940‑591‑4201.

Recall number 05V543000 · Recall details

What is wrong

On certain heavy duty trucks, the pivot bolts which hold the seat back frame to the seat cushion frame can loosen and possibly fracture or dislodge, causing the seat back to fail to provide full support to the driver.

Risk

A possible vehicle crash could occur should the seat fall backwards during use.

Remedy

Gra-mag will provide customers with repair kits which include instructions and parts to repair the seat. Owners should contact gra-mag at 614‑875‑8435 or peterbilt at 940‑591‑4201.

Recall number 04V548000 · Recall details

What is wrong

On certain trucks equipped with dana spicer integral knuckle and steer arm assemblies, the steer axle assemblies may have a longitudinal crack in the steer arm.

Risk

If the crack should propagate over time, the ball could become loose resulting in a loss of steering, which could result in a crash.

Remedy

Dealers will inspect and replace the knuckle and steer arm assemblies. Owner notification began january 5, 2004. Owners should contact kenworth at 1‑425‑828‑5440 or peterbilt at 1‑940‑591‑4201.

Recall number 03V410000 · Recall details

What is wrong

On certain trucks equipped with jost international jsk 37u series fifth wheels, a fatigue crack can develop in the bracket pin weld under certain loading conditions.

Risk

If left undetected or corrected it could lead to the separation of the fifth wheel top plate from its mounting structure, possibly resulting in a crash.

Remedy

Dealers will replace the bracket pins and repair instructions free of charge. Peterbilt's owner notification began june 20, 2003. Kenworth's owner notification began june 12, 2003. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact peterbilt at 940‑591‑4201 or kenworth 425‑828‑5440.

Recall number 03V168000 · Recall details

What is wrong

On certain trucks equipped with truck hub units manufactured by skf exclusively for use on arvinmeritor's ff98x series non-drive steer axles, the hub unit bearings can wear prematurely.

Risk

Seizure of the bearings can cause wheel separation or wheel end fire.

Remedy

Dealers will replace all front axle hubs. Notification began july 16, 2003. The manufacturer has advised us that parts will not be available until september 2003. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy with a reasonable time should contact peterbilt at 940‑591‑4201 or kenworth 425‑828‑5440.

Recall number 03V125000 · Recall details

What is wrong

On certain vehicles equipped with bendix tc-7 trailer control hand-operated valve with push-to-connect fittings. The delivery port in the valve body may be partially blocked due to a problem during the molding process.

Risk

Such blockage may slow the delivery and exhaust of air to and from the trailer brakes when they are operated by this hand-operated trailer control valve.

Remedy

Paccar will notify its customers and inspect and replace, if necessary, the hand valve free of charge. Owner notification began october 18, 2002. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact peterbilt at 940‑591‑4201.

Recall number 02V241001 · Recall details

What is wrong

Heavy duty trucks equipped with trw tie rod ends on certain arvinmeritor and dana axles. Peterbilt will recall 1,434 vehicles equipped with arvinmeritor axles manufactured from december 11, 1999, to may 14, 2000, and from july 22 to september 30, 2000. Kenworth will recall 859 vehicles equipped with arvinmeritor vehicles manufactured from december 11, 1999, to may 23, 2000, and from july 27, 2000, to september 30, 2000 and kennworth will recall an additional 4,151 vehicles equipped with dana axles and manufactured from june 23 to december 6, 1999, and from may 23 to september 30, 2000. The tie rod and drag link ball stud ends contain bearings that are below the specified case depth and/or hardness.

Risk

This can lead to premature wear with possible separation of the ball stud from the socket, increasing the risk of loss of control of the vehicle.

Remedy

Dealers will remove and replace all affected tie rods and drag links with different designed ends. Owner notification began july 15, 2002. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact peterbilt at 1‑940‑591‑4201 or kenworth at 1‑425‑828‑5440.

Recall number 02V037003 · Recall details

What is wrong

On certain heavy duty trucks equipped with meritor wabco pneumatic anitlock brake system (ABS) valve packages, the assembly bolts on these valve packages were not tightened correctly.

Risk

Bolts torqued below specification will not reliably prevent air leakage at the affected ABS valve package interface joints once the component begins normal vehicle operation. If air leaks develop at any of the ABS valve package interface joints, brake system pressure reductions could occur during braking or normal operation with units equipped with the traction control option, potentially extending stopping distances, possibly resulting in a vehicle crash.

Remedy

Dealers will tighten the fasteners to the proper specification. Owner notification began february 15, 2002. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1‑425‑828‑5440 or peterbilt at 1‑940‑591‑4201.

Recall number 02V018001 · Recall details

What is wrong

Vehicle description: heavy duty trucks equipped with trw tie rod ends on certain meritor axles. The tie rod and drag link ball stud ends contain bearings that are below the specified case depth and/or hardness.

Risk

This can lead to premature wear with possible separation of the ball stud from the socket, increasing the risk of loss of control of the vehicle.

Remedy

Dealers will remove and replace all affected tie rods and drag links with different designed ends. Owner notification began october 24, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact peterbilt at 1‑940‑591‑4000 or kenworth at 1‑425‑828‑5000.

Recall number 01V140006 · Recall details

What is wrong

Vehicle description: heavy duty trucks. These vehicles are equipped with peterbilt's smartgage system containing a reduced function interface module (rfim). This module receives data from various components/systems on the vehicle then sends the information to a microprocessor. A manufacturing defect in the rfim's can allow water to penetrate into the pressure block portion of the module, causing an electrical short in the pressure transducer connector.

Risk

This results in an erroneous air pressure reading on the gauge in the dash.

Remedy

The rfim date code will be inspected and all rfim's built prior to september 9, 2000 will be replaced. Owner notification began june 13, 2001. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact peterbilt at 1‑940‑591‑4000.

Recall number 01V131000 · Recall details

What is wrong

Vehicle description: heavy duty trucks equipped with tie rod assemblies manufactured by trw. The suspect tie rods contain 24-dl model ball sockets. Certain of the tie rod ball-socket bearings have a below-specification case depth and/or hardness, which can lead to premature wear of the socket.

Risk

If this condition occurs, the driver can lose partial control of the right front wheel, possibly resulting in a crash.

Remedy

Dealers will replace the defective ball sockets and/or drag links. Owner notification began on april 10, 2001, to kenworth owners and on april 25, 2001, to peterbilt owners. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact kenworth at 1‑425‑828‑5000, peterbilt at 1‑940‑591‑4000 or trw customer service at 1‑866‑280‑3287.

Recall number 01V044005 · Recall details

What is wrong

Vehicle description: heavy duty trucks. The side fairing hinge bar and mounts can detach from the fuel tank straps. The hinge bar can rotate and separate from the fairing, allowing the hinge bar assembly to fall off of the vehicle.

Risk

This could cause a road hazard, increasing the risk of a crash.

Remedy

Dealers will install an additional nut plate and if the bracket is cracked, the fuel tank strap will be replaced with a new strap and bracket assembly.

Recall number 00V185000 · Recall details

What is wrong

Vehicle description: heavy duty trucks. The steer axle mudflaps and/or mudflap stiffeners can rub a hole in the forward surface of the undercab fuel tank, causing a hole in the fuel tank.

Risk

This can result in fuel leakage. Fuel leakage in the presence of an ignition source could result in a fire.

Remedy

Dealers will provide replacement mudflap assemblies smaller than the original assemblies to owners and the fuel tank will be checked for abrasion and replaced if damaged.

Recall number 00V161000 · Recall details

What is wrong

Vehicle description: heavy duty trucks. There is an interference between the throttle pedal and the brake pedal.

Risk

The brake pedal may not operate as intended, resulting in greater brake pedal effort and/or delayed brake release.

Remedy

Dealers will replace the throttle pedal bracket.

Recall number 00V017000 · Recall details