I have a 2020 Subaru Outback with just over 70,000 miles on it. Well before hitting 70,000 miles, there were two occasions where a loud, unusual noise occurred while reversing out of my garage. Additionally, I occasionally hear a strange noise when shifting into Reverse from Park. I also sometimes notice a whining or humming sound when accelerating from a complete stop, such as at a traffic light. Regarding the two loud noises I experienced, I have saved an audio file recorded by another consumer who posted it online describing the exact same issue — the sound is identical to what my car produced on those two occasions. The audio file is available upon request and may assist in diagnosing the issue. Please note that the date I provided for when the noise first occurred is approximate, as I cannot recall the exact date. Since the noise occurs most frequently during reverse, I am concerned there may be an issue with the CVT transmission.
Subaru Outback cvt failure problems
162 of the 9,792 owner complaints about the Subaru Outback describe cVT failure, most of them for the 2011 model year.
- owner complaints
- 162
- worst model year
- 2011
- typical repair cost reported
- $7,000
- typical mileage
- 106,600
By model year
Often reported together
Stalling 74Transmission failure 22Shudder 22Jerking 17Hesitation 12Check engine light 6Warning lights 5Slipping 5
Trouble codes mentioned
P2764 1P2762 1P0867 1P0700 1C0282 1C0232 1C0231 1C0057 1C0045 1
What owners say
Brand new 2026 Outback experienced a "Sudden Unintended Acceleration / Brake Ineffectiveness. This occurred 3 times this week after the car had been driven over 90 miles or over 90 minutes. Engine and components were warmed up. Car was initially reported to dealer 10/6, car was examined by dealer and returned to me later that day.could not be replicated. Car sat at my home until today when it was driven over 90 minutes or 90 miles. Replicated failure by me same as earlier in the week . Car drivetrain felt surged. CVT fighting brake system when trying to turn car at street corner. Would not stop until on straight away ( seems to be triggered when turning and car was hot and when no power applied to engine. Only stops on straight away.. Could be related to cvt torque converter? Software glitch? Force of turning wheel?
Subaru Outback 2019 - Transmission CVT and Clutch failed at 6 years 103,000 miles. Transmission Slipped while driving (safety issues) and also clutch lurched/jumped (safety issue) when shifting eg reverse to drive. Common issue for 2010-2018 in manufacturers TSB. My car is 2019, and this was not included per dealer, cost $8000 for rebuilt transmission form Dealer. Subaru claimed no responsibility as normal wear despite car properly maintained.
Noticed minor hesitation in the reverse down our driveway Aug 2024. By Aug 2026, the transmission hesitation has turned into very noticeable shudder and slip. In reverse down the driveway, the TR580 CVT was showing premature initial failure resulting in unexpected loss of motive power control as well as acceleration hesitation in forward. This transmission defect compromised the ability to safely navigate down the driveway and through traffic, creating an risk of a rear end collision and stranding the vehicle in a hazardous roadway position. The vehicle was driven to Austin Subaru dealer early September 2026 where certified technicians inspected it. They diagnosed a catastrophic internal failure that is pending and stated the entire transmission assembly requires complete replacement. We were quoted an out of pocket retail repair cost of $9,774. Additional consideration: This defect occurred at exceptionally low mileage (<37,000) on a well maintained vehicle as it included Subaru provided services through April 2025. Only had a single oil change at a third party. Furthermore, Subaru of America Corporate Customer Advocacy was contacted regarding this exact VIN. Despite Subaru previously issuing a warranty extension program for identical transmission "judder" and slipping defects on 2019-2020 models (extending coverage to 10 years/100,000 miles), corporate formally denied coverage for my vehicle. This indicates that the dangerous premature CVT failure defect extends beyond the specific manufacturing batches Subaru has currently acknowledged, leaving drivers exposed to sudden loss of propulsion at highway speeds. I am requesting the federal safety agency investigate the 2020 Subaru Outback TR580 CVT for inherent safety defects leading to sudden loss of motive power.
2010-2018 TR580 Outback Torque Converter Lock-up failure symptoms in TSB 16-90-13R fits my 2011 Subaru Outback. 2.5I Premium, (TSB) Originally issued on 1/6/2014 + later revised on 5/7/2014, Early yrs of the TR580 suffer from TCLUF, which causes stalls + bogs down during stops or idling at traffic lights, premature wear, valve-body/solenoid failure, overheating, breakdown of transmission fluid/coolant + Catastrophic Chain Failure. These issues were exacerbated by Subaru specifying these transmissions have a "lifetime fluid" that never has 2 be replaced. Most Subaru failures were related 2 fluid breakdowns. The Subaru lineartronic CVT, designed in house by Subarun2 integrate w the company's longitudinal boxer engines + AWD system, built by Subaru in Ōizumi, Town in Ora District, Gunma Prefecture, Japan. lineartronic launched about 7 yrs after Nissan's 2003 X-Tronic CVT arrived here. Nissan had lots of trouble w early CVT's which led 2 transmission failures. As is the case w most new tech in a specific market sector, especially CVT's, the most Subaru CVT problems occurred in the 1st few model yrs. Each time my family or myself drive we are putting our lives in dire jeopardy, risk + danger of wrecking + even lost of life, too many close calls by peeps that almost rear ended us at a light, because of bogging down or almost stalling. The engine shudders + RPM drops very low as the vehicle stops, feeling as though a man trans car is stopping w/o a clutch being pressed. The problem was never fixed or looked into by 2 different dealerships + even though Subaru issued TSB 16-90-13R, identified wear of internal torque converter thrust washer as that wear can prevent lock up clutch from releasing properly, effectively keeping engine mechanically connected 2 transmission as vehicle stops. Subaru's corrective part used a needle bearing design instead of the earlier solid bushing. [XXX] on test drive about issue + was told nothings wrong, Car got inspected every yr since 16 w INFORMATION REDACTED PURSUANT TO THE FREEDOM OF
The CVT transmission in my 2013 Subaru Outback failed at approximately 93,000 miles. Approximately three weeks prior to the failure, I noticed an unusual sound while driving, but no other symptoms were apparent at that time, so I continued monitoring it. On the day of the failure, the rear tires began hopping and I lost acceleration while driving. Fortunately, this occurred while I was on my driveway, so I did not need to continue driving further. I parked the vehicle there and had it towed to my mechanic, and later to Rairdon Subaru of Auburn (WA), where the failure was diagnosed by their service department. The vehicle is available for inspection there. This loss of power and erratic rear-end behavior created a safety risk, as the same failure occurring while driving on a road could have affected the vehicle's ability to accelerate and respond predictably in traffic. This is a known issue: Subaru's own Technical Service Bulletin 16-107-17R acknowledges CVT transmission problems in 2010–2015 model year Outbacks and other models, and extended the powertrain warranty coverage for this issue to 10 years or 100,000 miles. My vehicle has only about 93,000 miles, but Subaru is denying full warranty coverage because the vehicle is outside the 10-year time limit, despite being well under the mileage limit. The vehicle has not been inspected by police or insurance representatives — this was a mechanical failure, not a collision.
Needed to move quickly out of way of oncoming traffic, but delay/hesitation in CVT made it almost impossible to avoid traffic.
The CVT failed at 62 miles per hour on a busy interstate, XXX. This caused the drivetrain to lock. The car has been repaired and traded locally in [XXX]. The car was very difficult to steer with locked wheels in traffic. This was a rapid evasive manuver on a busy interstate. An undrivable vehicle on an interstate is life threatening to many. Flat bed driver told me I was lucky to steer off of lanes onto shoulder with four locked wheels. This incident put me in mild shock. The Subaru dealer had to replace the transmission. The dealer and Subaru Regional Rep. examined the CVT failure. It was outside of the 100,000-mile warranty by about 895 miles. Repair invoice attached. I did not have advanced warning of CVT failure. There were no warning lights on before the CVT failure. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
While driving the 2016 Subaru Outback, the vehicle experienced a sudden, catastrophic failure of the Continuously Variable Transmission (CVT). The transmission completely failed, resulting in an immediate and dangerous loss of propulsion while operating the vehicle. This created an immediate safety hazard for myself, my toddler and other drivers on the road, as the vehicle could no longer maintain speed or accelerate safely to clear traffic. A certified repair facility diagnosed the issue as a complete internal mechanical failure of the transmission, requiring a total replacement at an estimated cost of roughly $11,000. This generation of Subaru CVTs has a well-documented history of premature, catastrophic mechanical failure, which Subaru of America has previously acknowledged via past warranty extensions. The sudden loss of power caused by this engineering defect poses a severe and ongoing safety risk to consumers. [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
SUBJECT: Formal Safety Defect Complaint: 2016 Subaru Outback – Manufacturing Nondisclosure of Latent "Day 1" Design Flaw Causing Ignition Key Entrapment, Uncommanded Steering Column Lockout, and Severe Family Safety Risk I am writing to formally report a severe, unaddressed safety defect and a deceptive corporate practice by Subaru of America, Inc. affecting my 2016 Subaru Outback. This vehicle suffers from a "Day 1" latent engineering flaw that causes the physical ignition key to become permanently trapped in the ignition cylinder, triggering an uncommanded, rigid locking of the steering column assembly. Subaru has possessed documented knowledge of this failure for years, cataloging it under Technical Service Bulletin TSB 16-112-18R. Rather than fulfilling its statutory obligation to issue a comprehensive federal safety recall, Subaru deployed a voluntary, time-bound 8-year warranty extension. Subaru conveniently did not notify me of this warranty extension. By doing so, the manufacturer unconscionably ignored this defect, placing its customers at direct peril. They capitalized on asymmetric information to shift both the financial burden and the severe physical safety risks of a known factory flaw onto my family, the moment an arbitrary time threshold expired. My family and I have been at active, continuous risk in this vehicle since the day we purchased it due to an engineering error that was present when the car rolled off the assembly line. The root cause of this failure is a fundamental engineering defect within the Continuously Variable Transmission (CVT) shifter assembly, specifically, the premature degradation of the electrical contacts within the select lever park-range switch.
Related recalls
Power train: automatic transmission: park/neutral start interlock switch
- What is wrong
- Subaru of America, Inc. is recalling certain model year 2021 Crosstrek, 2022 Forester, 2021-2023 Legacy, and Outback vehicles. An insufficient weld may allow water to enter the inhibitor switch, causing it to fail.
- Risk
- An inoperative inhibitor switch may prevent the reverse lights from illuminating and the rearview camera image from displaying, increasing the risk of a crash.
- Remedy
- Dealers will replace the inhibitor switch, free of charge. Owner notification letters were mailed January 8, 2024. Owners may contact Subaru customer service at 1‑800‑782‑2783. Subaru's number for this recall is WRQ-23.
Recall number 23V755000 · Recall details
Power train: driveline: driveshaft
- What is wrong
- Subaru of America, Inc. (Subaru) is recalling certain 2023 Outback, Legacy, Ascent, and Impreza vehicles. The center support bolts for the driveshaft may loosen, resulting in the disconnection of the front end of the driveshaft.
- Risk
- Separation of the front end of the driveshaft increases the risk of a crash.
- Remedy
- Dealers will clean the bolt mounting surfaces of the center support brace and install new bolts, free of charge. Owner notification letters were mailed November 20, 2023. Owners may contact Subaru's customer service at 1‑844‑373‑6614. Subaru's number for this recall is WRN-23.
Recall number 23V647000 · Recall details
Power train: driveline: chain/belt
- What is wrong
- Subaru of America, Inc. (Subaru) is recalling certain 2020-2021 Outback and Legacy vehicles. A programming error in the Transmission Control Unit (TCU) may allow the clutch to engage before the drive chain is completely clamped.
- Risk
- An improperly secured drive chain may slip and break, causing a loss of drive power and increasing the risk of a crash.
- Remedy
- Dealers will reprogram the TCU, inspect TCU data for chain slip, and visually inspect the chain guide. If evidence of chain slippage or damage is found, the transmission will be replaced. Repairs will be performed free of charge. Owner notification letters are expected to be mailed August 24, 2022. Owners may contact Subaru's customer service at 1‑844‑373‑6614. Subaru's number for this recall is WRK-22. This recall is an expansion of previous recall number 21V‑955.
Recall number 22V485000 · Recall details
Power train: driveline: chain/belt
- What is wrong
- Subaru of America, Inc. (Subaru) is recalling certain 2019-2020 Ascent, 2020 Legacy and Outback vehicles. A programming error in the Transmission Control Unit (TCU) may allow the clutch to engage before the drive chain is completely clamped.
- Risk
- An improperly secured drive chain may slip and break, causing a loss of drive power and increasing the risk of a crash.
- Remedy
- Dealers will reprogram the TCU, inspect TCU data for chain slip, and visually inspect the chain guide. If evidence of chain slippage or damage is found, the transmission will be replaced. Repairs will be performed free of charge. Owner notification letters were mailed August 19, 2022. This recall includes all vehicles previously recalled under 19V‑855. Vehicles previously recalled under 19V‑855 will need to have the new remedy performed for this recall once available. Owners may contact Subaru customer service at 1‑844‑373‑6614. Subaru's number for this recall is WRK-21.
Recall number 21V955000 · Recall details
Power train: shift linkage/cable/rod
- What is wrong
- Subaru of America, Inc. (Subaru) is recalling certain 2021 Outback and Impreza vehicles. The continuously variable transmission (CVT) select lever cable nut may not have been tightened properly, allowing the nut to loosen.
- Risk
- A loose nut can lead to a lost of retention in the CVT select lever cable and the gear selector not functioning properly, increasing risk of crash.
- Remedy
- Subaru will notify owners, and dealers will inspect, and, if necessary, tighten the nut, free of charge. The recall began February 12, 2021. Owners may contact Subaru customer service at 1‑844‑373‑6614. Subaru's number for this recall is WRA-21.
Recall number 21V024000 · Recall details
Power train: driveline: differential unit
- What is wrong
- Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
- Risk
- If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
- Remedy
- Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1‑856‑488‑8500. Subaru's number for this recall is WQV-57.
Recall number 15V794000 · Recall details
Power train: automatic transmission
- What is wrong
- Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
- Risk
- If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
- Remedy
- Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1‑800‑782‑2783. Subaru's number for this recall is WQU-56.
Recall number 15V502000 · Recall details
Power train: automatic transmission
- What is wrong
- Subaru of America is recalling certain model year 2014 Legacy 3.6R and Outback 3.6R and 2013 Tribeca vehicles manufactured June 12, 2013, through June 28, 2013 and equipped with 5-speed automatic transmissions. In the affected vehicles, the parking rod may come loose inside the automatic transmission.
- Risk
- As a result of the parking rod detaching, the transmission may not be able to be moved from the "park" position preventing the vehicle from being moved or driven. Furthermore, even with the transmission shifted into the 'park' position, the parking mechanism may not engage, and the vehicle may roll away while in the "park" position, increasing the risk of a crash.
- Remedy
- Subaru will notify owners, and dealers will replace the transmission, free of charge. The recall began during August 2013. Owners may contact Subaru at 1‑800‑782‑2783. Subaru's recall number is WQJ-46.
Recall number 13V336000 · Recall details
Power train: manual transmission
- What is wrong
- Subaru is recalling certain model year 2010 and 2011 outback and legacy passenger vehicles manufactured from april 28 through june 23, 2010. Due to a programming error, a lubrication hole within the 6-speed manual transmission was omitted.
- Risk
- If the transmission gears are not properly lubricated, a groaning sound may begin to develop alerting the driver of a problem. If the sound is ignored and no action is taken, the gears will eventually break and this condition will lead to vehicle power loss, possibly resulting in a crash.
- Remedy
- Subaru will notify owners and dealers will repair the vehicles by drilling an oil lubrication hole and, if necessary, replace the internal parts with new ones free of charge. The safety recall began on july 28, 2010. Owners may contact subaru at 1‑800‑782‑2783.
Recall number 10V326000 · Recall details
Power train: automatic transmission
- What is wrong
- Certain sport utility and passenger vehicles equipped with automatic transmissions were produced with an improperly manufactured transmission parking rod. When the transmission selector lever is placed in the "p" (park) position, the transmission park mechanism, that is intended to hold your vehicle, may not engage.
- Risk
- The vehicle could then move/roll without prior warning, increasing the risk of a crash.
- Remedy
- Dealers will replace the automatic transmission parking rod assembly. Owner notification january 8, 2003. An interim owner notification will be sent during november 2002. Owners who take their vehicles to an authorized dealer on an agreed upon service date and do not receive the free remedy within a reasonable time should contact subaru at 1‑800‑782‑2783.
Recall number 02V282000 · Recall details
Questions about the Subaru Outback cvt failure
Which Subaru Outback years have cVT failure problems?
The model years with the most reports are 2011 (44 complaints), 2012 (26 complaints) and 2010 (24 complaints).
How much does it cost to fix CVT failure on the Subaru Outback?
Owners who mentioned a price put the repair at about $7,000 (median of 38 complaints that include a dollar amount). Costs vary with mileage, warranty and where the work is done.
VIN decoder
See the problems and recalls for an exact car
Buying a used Subaru Outback?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history