I have been having a problem with the seatbelts on this Sequoia for many years and I have had to go into the dealership several times to get help with stuck seatbelts, seatbelts that didn’t retract and seatbelts that weren’t tight enough. I was told after a service visit that Toyota approved a rear middle row seatbelt replacement, but started having other mechanical issues and never scheduled the repair. After getting help for the last time I instructed my kids to be very gentle with the seatbelts and that seemed to help for a long time. They weren’t tight enough, but they were retractable if pulled slowly and carefully. They did get stuck again, but I carefully fed them back into the tract. Well, now I have a seatbelt that will not retract and that Is fully pulled out and not functioning at all, which is a serious safety risk for my daughter and any other passengers that may be in my vehicle. Toyota is now claiming that they have no case file about this issue and that I’m out of luck and will need to pay for the repair myself. It’s terrible that Toyota can hide serious safety design flaws, fail to input claims as promised, not input complaints when you visit for a concern, and not be punished. This is a flawed lifesaving automobile feature that should be corrected.
The worst 2008 Toyota Sequoia problems
Ranked by number of owner complaints. Mileage and cost come from what owners wrote.
- Body16
- Acceleration9
- Engine9
- Transmission7
- Brakes6
Problems by type
Tap a problem to see which part fails, at what mileage and in which other years.
- Body16
- Acceleration9
- Engine9
- Transmission7
- Brakes6
- Electrical5
- Seat belts5
- Suspension5
- Driver assistance3
- Seats3
- Tires3
- Steering2
- Airbags1
- Fuel system1
- Lights1
- Locks1
- Visibility1
- Wheels1
Recalls 8
Steering: rack and pinion
- What is wrong
- Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2008-2022 Sequoia and 2007-2021 Tundra vehicles. The power steering gear assembly may have been manufactured incorrectly, which can result in an oil leak.
- Risk
- An oil leak may cause a sudden loss of power steering assist, increasing the risk of a crash.
- Remedy
- Dealers will inspect and replace the power steering gear assembly as necessary, free of charge. Owner notification letters were mailed on January 21, 2022. Owners may contact Toyota customer service at 1‑800‑331‑4331. Toyota's numbers for this recall are 21TB10 and 21TA10.
Recall number 21V920000 · Recall details
Seats: front assembly: seat heater/cooler
- What is wrong
- Southeast Toyota Distributors, LLC (SET) is recalling certain 2005-2011 4Runner, Highlander, Sequoia, and Sienna, 2005-2010 Avalon and Tundra, 2006-2008 Camry Solara, 2006-2010 Highlander hybrid, 2006-2011 Rav4 and Tacoma, 2007-2010 FJ Cruiser, 2007-2011 Camry hybrid, 2009-2010 Venza, 2010-2012 Prius, 1988-1990 and 2005-2010 Camry, and 1989 and 2009-2010 Corolla vehicles equipped with aftermarket accessory seat heaters with a copper strand heating element. The electrical wiring in the seat heaters may be damaged when the seat cushion is compressed.
- Risk
- If damaged, the copper strand heating element may short circuit, increasing the risk of a fire.
- Remedy
- SET will notify owners, and dealers will disconnect the seat heaters, free of charge, and refund the purchase price of the seat heater accessory. The recall began on July 14, 2016. Owners may contact SET customer service at 1‑866‑405‑4226. SET number for this recall is SET16B.
Recall number 16V396000 · Recall details
Seats: front assembly: seat heater/cooler
- What is wrong
- Southeast Toyota Distributors, LLC (SET) is recalling certain model year 2010-2011 Prius and Corolla, 2009-2011 Venza, 2006-2010 Avalon, 2007-2010 FJ Cruiser, 2005-2011 Sienna and Sequoia, 2006-2011 Tacoma 4x2 and 4x4, Camry, Highlander, Tundra 4x2 and 4x4, and 2007-2011 Rav4 and 4Runner. The affected vehicles may experience compression of the seat cushion which may damage the seat heater wiring.
- Risk
- Damage to the seat heater wiring could cause the wires to short, increasing the risk of the seat burning and causing personal injury to the occupant.
- Remedy
- SET will notify owners, and dealers will disconnect the heaters with copper strand heating elements and refund the purchase price of the seat heater accessory, free of charge. The recall is expected to began in January 2015. Owners may contact SET customer service at 1‑866‑405‑4226.
Recall number 14V743000 · Recall details
Visibility: power window devices and controls
- What is wrong
- Toyota is recalling certain model year 2007-2009 Camry, Camry Hybrid, RAV4, Corolla, Corolla Matrix, Tundra, Sequoia, Highlander, Highlander Hybrid, Yaris, Scion xB, Scion xD and Pontiac Vibe vehicles. The power window master switch assemblies in some of these vehicles were built using a less precise process for lubricating the internal components of the switch assemblies. Irregularities in this lubrication process may cause the power window master switch assemblies to malfunction and overheat.
- Risk
- If the switch overheats, it may melt, possibly resulting in a fire.
- Remedy
- Toyota will notify its owners, and dealers will inspect the switch and apply a special grease that inhibits heat build up or replace any switch damaged by the defect, free of charge. Toyota owners that experience a problem with a switch should not attempt to make repairs, but should contact their Toyota dealer or the Toyota Customer Experience Center at 1‑800‑331‑4331. General Motors will contact the Pontiac Vibe owners affected by this recall and GM dealers will inspect and repair switches as necessary. Those owners may contact Pontiac Customer Care at 1‑800‑762‑2737.
Recall number 12V491000 · Recall details
Tires: pressure monitoring and regulating systems
- What is wrong
- Toyota is recalling certain model year 2008 through 2011 fj cruiser, land cruiser, tacoma, sequoia and tundra vehicles for failing to comply with the requirements of federal motor vehicle safety standard no. 138, "tire pressure monitoring system (TPMS)." when factory-installed wheels and tires were replaced with toyota authorized accessory wheels and lt tires prior to first sale, the tire pressure monitoring systems were not re-calibrated correctly and therefore do not start illuminating the low tire pressure warning telltale at the required minimum activation pressure.
- Risk
- Failure to warn of tire deflations is a non-compliance with fmvss 138 and could lead to tire failure increasing the risk of a crash.
- Remedy
- For the land cruiser, sequoia, tacoma and tundra vehicles, the dealer will re-calibrate the tire pressure monitoring system on affected vehicles and install an updated tire and loading information label at no charge. For the fj cruiser vehicles, the TPMS cannot be reset so the electronic control unit (ecu) for the TPMS will be replaced. Toyota is currently developing the remedy ecu. If an owner is not certain whether his or her vehicle is equipped with these accessories, please contact any toyota dealer for an inspection at no charge. The safety recall began on march 31, 2011. Owners may contact toyota at 1‑800‑331‑4331.
Recall number 11V148000 · Recall details
Equipment: other: labels
- What is wrong
- Gulf states toyota is recalling certain model year 2005-2010 vehicles for failing to comply with the requirements of federal motor vehicle safety standard no. 110, "tire selection and rims." these vehicles were sold between september 1, 2005 and june 2, 2008 without the requisite load carrying capacity modification labels.
- Risk
- This does not meet the standard requirements.
- Remedy
- Dealers will mail to consumers the corrected label or the customer will have the option for dealers to install the label free of charge. Dealers will also correct the owner's manual. The safety recall began on may 27, 2010. Owners may contact gulf states toyota at 713‑580‑3300.
Recall number 10V035000 · Recall details
Equipment: other: labels
- What is wrong
- Southeast toyota is recalling certain model year 2005-2011 passenger vehicles for failing to comply with the requirements of federal motor vehicle safety standard no. 110, "tire selection and rims." these vehicles were sold without the requisite load carrying capacity modification labels.
- Risk
- A driver may overload a vehicle which may increase the risk of a crash.
- Remedy
- Dealers will mail to consumers the corrected label or the customer will have the option for dealers to install the label free of charge. The safety recall began on may 27, 2010. Owners may contact southeast toyota at 1‑800‑301‑6859.
Recall number 10V036000 · Recall details
Vehicle speed control: accelerator pedal
- What is wrong
- Toyota is recalling certain model year 2005-2010 avalon, model year 2007-2010 camry, model year 2009-2010 corolla, corolla matrix, rav4, model year 2010 highlander, model year 2008-2010 sequoia, and model year 2007-2010 tundra vehicles. Due to the manner in which the friction lever interacts with the sliding surface of the accelerator pedal inside the pedal sensor assembly, the sliding surface of the lever may become smooth during vehicle operation. In this condition, if condensation occurs on the surface, as may occur from heater operation (without A/C) when the pedal assembly is cold, the friction when the accelerator pedal is operated may increase, which may result in the accelerator pedal becoming harder to depress, slower to return, or, in the worst case, mechanically stuck in a partially depressed position.
- Risk
- The accelerator pedal may become hard to depress, slow to return to idle, or, in the worst case, mechanically stuck in a partially depressed position, increasing the risk of a crash.
- Remedy
- Dealers will install a reinforcement bar in the accelerator pedal which will allow the pedal to operate smoothly. Gm will notify owners for the pontiac vibe please see 10v‑018. This service will be performed free of charge. The safety recall is expected to begin on february 5, 2010 and will be completed on march 15, 2010. Owners may contact toyota at 1‑800‑331‑4331.
Recall number 10V017000 · Recall details
Technical service bulletins for the 2008 Toyota Sequoia 241
Bulletins tell dealers how to fix known problems. A warranty extension means the manufacturer pays for that repair for longer.
- Condition in which a musty odor is present
- Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical...
- To prevent brake rotor rust from forming during transportation and storage, wheel film will be used...
- The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix...
- Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal...
- Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad...
- Condition in which a musty odor is present
- This Service Bulletin provides updated non-electric water pump leak inspection and diagnostic tips for...
- Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal...
- This is to advise of various price adjustments that will affect Toyota Genuine Motor Oil and Long Life...
2008 Toyota Sequoia fuel economy
Official EPA estimates in miles per gallon (MPGe for electric). Ranges cover trims that share the same engine.
| Engine | Drive | City | Highway | Combined |
|---|---|---|---|---|
| 4.7L 8‑cyl | RWD | 14 | 17 | 15 |
| 5.7L 8‑cyl | RWD | 14 | 19 | 15 |
| 5.7L 8‑cyl | 4WD | 13 | 18 | 15 |
| 4.7L 8‑cyl | 4WD | 13 | 16 | 14 |
What 2008 Toyota Sequoia owners say
Most recent owner complaints, unedited.
While accelerating to pass a vehicle that was signaling and operating well below the speed limit, my vehicle experienced sudden and continued unintended acceleration. I was able to bring the vehicle to a stop while fighting against the engine within an intersection but the engine continued building revs, bouncing off the limiter while my foot was entirely removed from the accelerator pedal and fully applied to the brake. During this time I had moved the gear selector to neutral, only furthering the engine's revs, and attempted to place the vehicle into park without success, before having to reach beneath my dashboard, foot still on the brake, to pull the accelerator pedal up. I verified both visually and by feel that the pedal was stuck in it's position entirely on it's own, there was no outside object or floormat inhibiting it's ability to return.
Odometer Fraud. The contact purchased a 2008 Toyota Sequoia. The contact discovered a mileage discrepancy after the purchase. The vehicle was a dealer sale. At the time of purchase, the vehicle mileage was 143,000. It was later discovered, when the contact received the Title, the mileage was 248,000.
The drivers seat belt sometime does not retract. One of the seat belts in the middle row retracts slowly or sometimes does not retract. Another seatbelt is very tough to pull out to buckle. I just purchased this vehicle so I’m not sure how long the seatbelts have been an issue.
My wife pulled out of a parking lot and there was a loud noise and the vehicle began to shudder violently. Approximate speed was 10 mikes an hour and she was able to stop. The drivers side rear suspension airbag had broken through the lower control arm, and was under the rear driver side tire. It appears some frame members are cracked as well. Had this happened at highway speeds, it may have resulted in a catastrophic accident. Writer contacted Toyota, as I do not recall being notified of their ZH9 frame replacement program that resulted from a class action settlement, and the rear of the frame is horribly rusted. Vehicle probably would have qualified at that time to be fixed, but am now out of the window. Manufacturers should be made to notify via certified mail, so they know their customers received notifications like this.
The contact owns a 2008 Toyota Sequoia. The contact stated that while the vehicle was at the independent mechanic for an oil change, the mechanic informed her husband that the chassis was severely rusted. The dealer and other unknown dealers were notified of the failure and informed the contact that they could not repair the vehicle under Toyota Campaign Number: ZH7 because the campaign had expired. The manufacturer was notified of the failure and confirmed the assessment from the dealers. The vehicle was not repaired. The failure mileage was approximately 30,000. The VIN was unavailable.
The contact owns a 2008 Toyota Sequoia. The contact stated that while the vehicle was in for routine service, the independent mechanic discovered that the rear subframe was severely damaged due to rust and corrosion. The contact was advised that holes were present in the subframe, and the vehicle was unsafe to drive. The vehicle was not repaired. The local dealer and manufacturer were notified of the failure and informed that the vehicle was no longer qualified under the Extended Warranty Coverage for the failure. The failure mileage was 168,000. The VIN was not available.
A valve spring in the engine failed causing one cylinder to fail as well. The failure fortunately happened at low speed and the engine didn't seize. This a known problem with Toyota V8s of this model year and was the reason for a recall of Lexus vehicles with the same engine. Had this happened at highway speed, the engine, we were told, could have experienced a total failure causing the engine to seize likely leading to a serious accident. The car is available for inspection at the moment, but this failure requires a total engine rebuild or an engine replacement which are both very costly and we may have to purchase a new car. The car has not been inspected by Toyota, police, insurance or anyone other than a car service center. There were no warning lights, messages or any symptoms prior to the failure. It was sudden with no warning at all. The car has been very well maintained over the years with regular maintenance done on a consistent schedule.
Activation of VSC off and slip indicator flashing.
The contact owns a 2008 Toyota Sequoia. The contact stated that while the vehicle was at the dealer for an unknown repair, the dealer informed the contact that the sub-frame was corroded. The vehicle was not repaired and remained at the dealer. The manufacturer was made aware of the failure. The failure mileage was approximately 125,000.
Compare the 2008 Toyota Sequoia
Sequoia vs Chevrolet TahoeSequoia vs Ford ExpeditionSequoia vs Chevrolet SuburbanSequoia vs GMC YukonSequoia vs Nissan Armada
Other model years
2001200220032004200520062007200820092010201120122013201420152016201720182019202020212022
Questions about the 2008 Toyota Sequoia
Is the 2008 Toyota Sequoia reliable?
Owners have filed 67 complaints about the 2008 Toyota Sequoia, 3.4 times a typical Sequoia model year. It is one of the years we flag to avoid.
What is the 2008 Toyota Sequoia year score?
The 2008 Toyota Sequoia scores 24 out of 100 (poor). The score compares it with the other model years of the Toyota Sequoia: 75 is a typical year, 50 means twice the usual complaints, and serious complaints and recalls lower it.
What is the most common problem with the 2008 Toyota Sequoia?
Body and structure, with 16 complaints, typically around 95,000 miles. Next is acceleration (9).
How many recalls does the 2008 Toyota Sequoia have?
8 recalls, covering steering, seats and visibility.
What year does the Toyota Sequoia have the most body problems?
The Toyota Sequoia model years with the most body complaints are 2001 (102 complaints), 2003 (98 complaints) and 2002 (95 complaints).
What gas mileage does the 2008 Toyota Sequoia get?
Official estimates for the 2008 Toyota Sequoia range from 14 to 15 mpg combined. The most efficient version (4.7L 8-cyl, RWD) gets 14 city and 17 highway.
VIN decoder
See the problems and recalls for an exact car
Buying a used 2008 Toyota Sequoia?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history