The engine was making a noise which was obviously coming from internally. Chevrolet dealer examined the engine and found metal shavings throughout. Lifter roller was stuck and grinding down the camshaft. The engine was at risk of failure which could have been catastrophic if it occurred while driving . Especially at higher speeds . This could have resulted in a crash.
Chevrolet Silverado 1500 grinding brakes problems
184 of the 18,180 owner complaints about the Chevrolet Silverado 1500 describe grinding or squealing brakes, most of them for the 2002 model year.
- owner complaints
- 184
- worst model year
- 2002
- typical repair cost reported
- $1,000
- typical mileage
- 40,383
Is there a fix? There are 8 recalls for this area of the car. See below
By model year
Often reported together
ABS 19Jerking 18Harsh shifting 17Engine failure 17Check engine light 17Knocking 16Brake failure 10Loss of power 8
Trouble codes mentioned
P0747 1P0700 1
What owners say
The 2026 Chevy 1500 Silverado 6.2L engine had a slight knocking sound from the date I purchased it brand new in march 2026. I was driving home on a evening in July 2026 and the truck began to squeak, knock very loudly and shake violently. The truck then locked up and completely shut off while I was driving 45 mph down the highway. The vehicle had approximately 3,000 miles on it when the incident occurred. The truck’s violent shaking and sudden loss of power while traveling 45 mph created an immediate risk in which I did not have control of the vehicle and could have caused me to be unable to safely maneuver out of traffic. Thank God there was light traffic at the time and also a wide empty parking lot straight ahead of me when the truck shut down. The incident also placed other drivers in danger of colliding with my disabled vehicle or taking sudden evasive action that could cause an accident. I had it towed directly to the dealership service department and according to their report, "found catastrophic internal engine failure."
The water pump went bad at 31,000 miles. If I continued driving and the pulley fell off the engine would overheat. I took it to the dealer and they confirmed the pump failure and want me to pay over $1,400 for repair that should be covered under warranty. There was no warning lamps lit, the pump just started making a grinding sound.
While driving at about 20mph we hear a grinding noise and the truck throws itself into nuetral and then shut off. The truck seems to be on like when started with the key fob, on but not fully started. A warning message comes on the dash stating "conditions not safe to drive". The truck would not go back into gear, even after pressing the start button and truck regaining power. Pressed on the brakes to stop, put in park and then back into drive. Message warning went off and truck drove as normal again. This has happened twice since purchasing the vehicle in May 2026.
Complete brake system, master cylinder, pads, rotors. Only 75000+- miles. Morning start and the brakes are locked up. Had to get towed and the entire system needed to be replaced. So after several days and almost $5,000 I started driving home. After about 5 miles something fell off the front brakes and bounced along underneath but I was close to home so I continued and didn't need to apply the brakes until my driveway and then a terrible grinding sound. Called the dealer (Modern Chevrolet) Winston-Salem NC. Turns out the Einsteins who did the work forgot to tighten the bolts holding the rotor and one fell out and the other one was grinding against the wheel. So another extended stay at the dealership to correct this, a new wheel and correction to the brake components.
The contact owns a 2025 Chevrolet Silverado 1500. The contact stated that while starting the vehicle remotely, an abnormal grinding and banging sound was heard emanating from the engine compartment. The vehicle independently shut off. The contact attempted to restart the vehicle remotely, but the vehicle shut off again. The contact then attempted to start the vehicle manually, but the vehicle failed to start. The vehicle was towed to the dealer, where it was diagnosed that the engine had failed and needed replacement. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 5,425.
I purchased a 2026 Chevrolet 1500 Duramax Deisel truck. At 9500 miles the truck started making popping and loud grinding noises and would shake while driving it. I barely made it to the dealership on August 6th 2026 I took it to Group 1 Chevrolet where I bought it in Houston,Texas and on August 8th was told that they need to replace the engine and do not have an estimated time for repair.
My truck (2025 Chevy Silverado Trail Boss LZ0 Duramax 3.0l) started to have problems when driving. At a stop light, I started to accelerate at about 2000-3000 RPM. While doing so, there was a loud ticking/grinding noise coming from the transmission/Bell housing area. On June 2nd, I dropped the truck off with the dealership. I didn’t hear back from them until about a month later (July 3rd) and when I did they said the technician confirmed I needed a new ‘axle actuator’. About a week and a half later, they said it did not fix the issue and started to become more of a problem to where they will need an “engine technician” to see if I need a new engine due to the “crank shaft thrust bearing”. The advisor said he will call me on Wednesday, July 15th to update me on what I will need. I requested a Loaner vehicle since I dropped it off and they said no because the dealer does not provide that and would have to get approval from GM to grant me the loaner vehicle bast off the diagnostic.
The contact owns a 2022 Chevrolet Silverado 1500. The contact stated that upon starting the vehicle, there was a message related to brakes. The contact stated that while driving at an undisclosed speed, the brake pedal was depressed, and there was an abnormal grinding sound coming from the brakes. There were no warning lights illuminated. The vehicle was taken to the local dealer, where it was diagnosed and determined that the brake pads and rotors needed to be replaced. The dealer informed the contact that the brake sensors had detached. The repair was not covered under warranty. The manufacturer was contacted and confirmed that the repair was not covered under warranty. The failure mileage was approximately 35,000.
Normal driving then heard a knocking and squealing. Was told it was a spun main bearing on the crack shaft.
Related recalls
Service brakes, hydraulic: power assist: electric: control module: software
- What is wrong
- General Motors, LLC (GM) is recalling certain 2023 Chevrolet Silverado 1500, GMC Sierra 1500, 2023-2024 Chevrolet Tahoe, Suburban, GMC Yukon, Yukon XL, Cadillac Escalade, and Escalade ESV vehicles. The electronic brake control module software may fail to display a warning light when a loss of brake fluid occurs. As such, these vehicles fail to comply with the requirements of Federal Vehicle Safety Standard number 135, "Light Vehicle Brake Systems."
- Risk
- Without a warning light, the vehicle may be driven with low brake fluid, which can reduce braking performance and increase the risk of a crash.
- Remedy
- The Electronic Brake Control Module (eBCM) software will be updated through an over-the-air (OTA) update or by a dealer, free of charge. Owner notification letters were mailed October 25, 2024. Owners can contact GMC customer service at 1‑800‑462‑8782, Chevrolet customer service at 1‑800‑222‑1020, or Cadillac customer service at 1‑800‑458‑8006. GM's number for this recall is N242447990.
Recall number 24V674000 · Recall details
Service brakes, hydraulic: power assist: vacuum
- What is wrong
- General Motors LLC (GM) is recalling certain 2018 Cadillac Escalade, Chevrolet Silverado 1500 and Tahoe, GMC Sierra 1500 and Yukon vehicles equipped with either a 5.3L or 6.2L V8 engine. The output of the mechanical vacuum pump can decrease over time, decreasing the amount of vacuum/power brake assist.
- Risk
- A decrease in brake assist can increase the brake pedal effort and distance required to stop the vehicle, increasing the risk of a crash.
- Remedy
- GM will notify owners, and dealers will reprogram the Electronic Brake Control Module, free of charge. The recall began November 11, 2020. Owners may contact GM customer service at 1‑866‑522‑9559, Cadillac customer service at 1‑800‑458‑8006 or Chevrolet customer service at 1‑800‑630‑2438. GM's number for this recall is N202300860.
Recall number 20V603000 · Recall details
Service brakes, hydraulic: foundation components: disc: caliper
- What is wrong
- General Motors LLC (GM) is recalling certain 2020 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles. The bolts used to attach the front and/or rear brake calipers may have not been heat treated and may break under load.
- Risk
- Broken caliper bolts can reduce brake performance or interfere with wheel rotation and increase the risk of a crash.
- Remedy
- GM will notify owners, and dealers will replace the brake caliper bolts, free of charge. The recall began March 23, 2020. Owners may contact Chevrolet customer service at 1‑800‑222‑1020 or GMC customer service at 1‑866‑522‑9559. GM's number for this recall is N202294420.
Recall number 20V116000 · Recall details
Service brakes, hydraulic: power assist
- What is wrong
- General Motors LLC (GM) is recalling certain 2019 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles. These vehicles received updated software for the Electronic Brake Control Module (EBCM). This software has an error, and as a result, the vehicle's electronic brake assist may be disabled. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 126, "Electronic Stability Control" and 135, "Light Vehicle Brake Systems."
- Risk
- A loss of electronic brake assist can increase the risk of a crash.
- Remedy
- GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began February 24, 2020. Owners may contact Chevrolet customer service at 1‑800‑222‑1020 or GMC customer service at 1‑888‑988‑7267. GM's number for this recall is N192268091.
Recall number 20V055000 · Recall details
Service brakes
- What is wrong
- General Motors LLC (GM) is recalling certain 2019 Chevrolet Silverado 1500, Cadillac CT6, and GMC Sierra 1500 vehicles. Due to an Electronic Brake Control Module (EBCM) software error, the vehicle's Electronic Stability Control (ESC) and Antilock Brake System (ABS) may become disabled. Furthermore, if this specific error occurs, the vehicle's diagnostics will not illuminate the instrument cluster ESC and ABS malfunction warning lights. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 126, "Electronic Stability Control" and 135, "Light Vehicle Brake Systems."
- Risk
- If the driver operates the vehicle unaware that ESC and ABS are not functioning, there is an increased risk of a crash.
- Remedy
- GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began February 4, 2020. Owners may contact Chevrolet customer service at 1‑800‑222‑1020, Cadillac customer service at 1‑800‑333‑4223, or GMC customer service at 1‑888‑988‑7267. GM's number for this recall is N192268090.
Recall number 19V889000 · Recall details
Service brakes, hydraulic: power assist: vacuum
- What is wrong
- General Motors LLC (GM) is recalling certain 2015-2017 Cadillac Escalade, 2014-2018 Chevrolet Silverado, GMC Sierra, 2015-2018 Chevrolet Suburban, Tahoe, GMC Yukon vehicles. The amount of vacuum created by the vacuum pump may decrease over time.
- Risk
- As the vacuum level drops, the brake assist decreases, increasing braking effort, extending the distance required to stop the vehicle, thereby increasing the risk of a crash.
- Remedy
- GM will notify owners, and dealers will reprogram the Electronic Brake Control Module, free of charge. The recall began October 8, 2019. Owners may contact Chevrolet customer service at 1‑800‑630‑2438, Cadillac customer service at 1‑800‑458‑8006 or GMC customer service at 1‑800‑462‑8782. GM's number for this recall is N192268490.
Recall number 19V645000 · Recall details
Service brakes, hydraulic: pedals and linkages
- What is wrong
- General Motors LLC (GM) is recalling certain 2015-2016 Chevrolet Silverado 2500, 3500, 1500 Crew Cab Special Service, Tahoe Police Pursuit/Special Service, GMC Sierra 2500, and 3500 vehicles. The brake pedal pivot nut may loosen, causing the brake pedal to be loose or inoperative.
- Risk
- If the brake pedal becomes loose or inoperative, the driver may be unable to stop the vehicle by using the brake pedal. Additionally, a loose pedal may also interfere with the accelerator pedal. Either condition may increase the risk of a crash.
- Remedy
- GM will notify owners, and dealers will add adhesive to the nut and reinstall the nut with increased tightness, free of charge. The recall began October 3, 2018. Owners may contact Chevrolet customer service at 1‑800‑222‑1020, or GMC customer service at 1‑800‑462‑8782. GM's number for this recall is 18278. Note: The vehicles in this recall need this additional remedy despite being covered by recall 16V069 for brake pedal loosening.
Recall number 18V578000 · Recall details
Service brakes, hydraulic: pedals and linkages
- What is wrong
- General Motors LLC (GM) is recalling certain model year 2015-2016 Chevrolet Silverado 1500, 2500, and 3500 heavy duty trucks manufactured October 1, 2013, to February 1, 2016, 2015-2016 Chevrolet Tahoe Police Pursuit Vehicles (PPV) manufactured March 1, 2014, to February 1, 2016, and 2015-2016 GMC Sierra 2500 and 3500 heavy duty trucks manufactured October 29, 2013, to February 1, 2016. On the affected vehicles, the brake pedal pivot nut may loosen, causing the brake pedal to be loose or inoperative.
- Risk
- If the brake pedal becomes loose or inoperative, the driver may be unable to stop the vehicle by using the brake pedal. Additionally, a loose pedal may also interfere with the accelerator pedal. Either condition may increase the risk of a crash.
- Remedy
- GM will notify owners, and dealers will add adhesive to the brake pedal pivot nut and reinstall with an increased torque, free of charge. The recall began on March 14, 2016. Owners may contact Chevrolet customer service at 1‑800‑222‑1020 or GMC customer service at 1‑800‑462‑8782. GM's number for this recall is 20760.
Recall number 16V069000 · Recall details
Questions about the Chevrolet Silverado 1500 grinding brakes
Which Chevrolet Silverado 1500 years have grinding or squealing brakes problems?
The model years with the most reports are 2002 (14 complaints), 2006 (13 complaints) and 2014 (12 complaints).
How much does it cost to fix grinding or squealing brakes on the Chevrolet Silverado 1500?
Owners who mentioned a price put the repair at about $1,000 (median of 23 complaints that include a dollar amount). Costs vary with mileage, warranty and where the work is done.
VIN decoder
See the problems and recalls for an exact car
Buying a used Chevrolet Silverado 1500?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history