1995 Dodge Stratus problems

What is wrong

On certain passenger vehicles, the floor shifter ignition-park interlock may fail and allow the shifter to be moved out of the park position with the key removed. An inoperative interlock may also allow the key to be removed when the shifter has not been placed in the park position.

Risk

Either circumstance may result in the vehicle rolling away without warning.

Remedy

Dealers will install a new load-limiting push rod into the floor shifter lever of the affected vehicles. Owner notification began on june 14, 2004. Owners should contact daimlerchrysler at 1‑800‑853‑1403.

Recall number 04V021000 · Recall details

What is wrong

Vehicle description: passenger vehicles equipped with automatic transmissions. The adjustment of the cable connecting the console shifter mechanism to the ignition key can cause a trapped key condition which can result in a low force required to depress the shift button. A combination of applying a mis-adjusted release button with a low force attempt to shift out of park with the key in the locked position, can break the connecting pin in the shifter.

Risk

If this happens, the "ignition-park" interlock system will be nonfunctional.

Remedy

Dealers will inspect for proper operation of the system. Any vehicles that are not functional after the inspection will have the shift mechanism and cable replaced with a "self-adjusting" design.

Recall number 98V183000 · Recall details

What is wrong

Vehicle description: passenger vehicles. The rear seat belt anchor does not achieve the loading required by fmvss no. 210, "seat belt assembly anchorages."

Risk

Failure of a seat belt anchor can result in the loss of seat belt protection, which could lead to serious injury or death in the event of a crash.

Remedy

Dealers will inspect the rear seat belt outboard anchor floor attachments for proper positioning. If the anchor was improperly oriented, the orientation will be corrected.

Recall number 98V063000 · Recall details

What is wrong

Vehicle description: passenger vehicles. The lower control arm ball joint can separate due to loss of lubrication.

Risk

Separation of the ball joint could cause a loss of steering control increasing the risk of a vehicle crash.

Remedy

Dealers will inspect the ball joint end housing cover seal for leakage with a high pressure air tester and the rubber boot will be visually inspected for damage. If the cover seal leaks or the boot is damaged, the lower control arm will be replaced.

Recall number 97V201000 · Recall details

What is wrong

The brake master cylinder can leak brake fluid due to a damaged double lip rear piston seal.

Risk

Brake fluid leakage can result in diminished effectiveness of one half of the split brake system. The instrument panel warning light(s) will signal system impairment prior to partial brake system loss.

Remedy

Dealers will replace the rear brake master cylindr piston assembly.

Recall number 96V075000 · Recall details

What is wrong

Corrosion of the ABS hydraulic control unit can cause the solenoid valves to stick in the open position.

Risk

If either front wheel valve sticks, the vehicle would swerve from a straight stop when the brakes are applied.

Remedy

Dealers will install a plate and silicone grease injected into the solenoid cavity to eliminate the potential for this condition.

Recall number 96V074000 · Recall details

What is wrong

In certain vehicles, the engine cylinder head oil galley plug does not seal properly and engine cylinder head oil is not adequately retained.

Risk

Inadequate sealing and retention of the plug can result in oil leakage which could cause a fire in the engine compartment.

Remedy

Dealers will install an expansion plug and retaining bracket over the cylinder head oil galley plug.

Recall number 96V006000 · Recall details

The manufacturer reports above are based on daimlerchrysler?s (dc) analysis of model year (my) 1998 (population = 356,384) and 1999 (population = 486,948) ja, jx and lh family subject vehicle data (earlier mys excluded).the population number includes all mys.the precise number of duplicates between odi and dc reports cannot be determined due to missing or incomplete information.the fatality incident involved an elderly person who attempted to stop a roll away vehicle and received fatal injuries.odi also gathered information on my 1997-99 prowler vehicles in this investigation. The prowler vehicles were manufactured with a different design shifter mechanism (the shift lever is shorter).there are no complaints of prowler interlock failure in odi?s database, and dc has received no reports either.the prowler is excluded from the recall scope.the investigation involved a condition where the interlock system could fail (or be made inoperative by the operator) during vehicle use, possibly inadvertently.the interlock system is required under fmvss 114.with the transmission in the park position and the ignition key off, the combined action of pressing the shift button and pulling the shift lever rearward may result in the operator overcoming the interlock system and cause the mechanical linkage of the system to disconnect.when this occurs, there is no overt indication to an operator that the system is defeated, and an increased risk of vehicle roll-away exists.under recall 04v021, dc will replace damaged shift mechanisms, and will install on all vehicles a device which inhibits the operator?s ability to overcome the interlock and defeat the system.beginning with my 2000, dc incorporated a brake and transmission shifter interlock (btsi) system into the subject vehicles.introduction of btsi involved design changes to the shift mechanism, one of which resulted in reduced mechanical advantage (rma) of the shift button.the rma shifter requires increased forces to overcome the interlock system, making the shifter less susceptible to damage.

EA03011

Mr. Larry a. Sackey submitted a petition to the federal safety agency by letter dated april 18, 2003, requesting that agencyfurther investigate the defective collapsible steering shaft system on 1987-1995 vehicles manufactured by the daimlerchrysler corporation.in part because of 49 cfr ? 30120(g), the federal safety agency has decided to limit the scope of the petition vehicles to 1993-1995 models, excluding the 1993 jeep grand cherokee and 1994-1995 dodge ram series trucks that were recalled (93v210 & 96v230) for steering column failure.if the analysis of these vehicles had identified a potential problem, the scope could have been expanded in an investigation.a review of odi's data base shows no recent complaints and a lack of a complaint trend concerning the subject issue on the subject vehicles as a whole or by individual models.therefore, the petition is denied.for details, see federal register notice volume 68, no. 130, july 8, 2003.

DP03002

There are no injuries or fatalities associated with this alleged defect.while conducting this investigation, odi found that the subject cinches meet the load bearing requirements of federal motor vehicle safety standard 208, and that many of the reported failures were due to incorrect child safety seat installations. Additionally, the report rate is low (1.60/100k).the information available fails to establish the existence of a defect trend at this time.further allocation of agency resources to this issue is unwarranted and the preliminary evaluation is being closed.

PE02082

By letter dated november 6, 1997, the manufacturer advised this agency of its decision to initiate a safety recall campaign of the subject vehicles to correct the defect identified in this ea.the recall will also cover 1996 and 1997 chrysler cirrus/dodge stratus vehicles, as well as 1995 through 1997 chrysler sebring convertible and plymouth breeze vehicles equipped with identical lower control arm ball joints.an estimated total of 599,00vehicles are affected by this recall.the manufacturer's investigation disclosed that process variability, together with the ball joint housing cover crimping operation, can result in an ineffective seal that permits a loss of lubrication and accelerted wear of the ball joint assembly.this condition can lead to failure and separtion of the lower control arm ball joint.the recall is identified as the federal safety agency 97v‑201 and a copy of chrysler's letter to the federal safety agency is attached hereto.

EA97016

The manufacturer identifed vehicle owner complaints of the subject ball joint failures as tabulated above.in addition, a total of 72 warranty reports were identified for replacement of broken or cracked ball joint assemblies in the subject vehicles.chrysler also reported that 1996 and 1997 models are equipped with identical ball joint assemblies as the subject 1995 model year vehicles.a partial response to the federal safety agency's information request indicated that the manufacturer's analyses and evaluations of the condition were continuing.in order to continue the federal safety agency's complete assessment of the nature and scope of this matter, this investigation has been upgraded to an engineering analysis.

PE97009