The contact owns a 2011 Mercedes-Benz ML350. The contact stated that while driving at an undisclosed speed, the brake pedal was depressed and went to the floorboard. The vehicle failed to stop at the stop sign. The contact swerved to the right and struck the curb. The vehicle was then driven to the residence. The manufacturer was made aware of the failure and informed the contact that the vehicle was previously repaired under the federal safety agency Campaign Number: 22V315000 (Service Brakes, Hydraulic). The failure mileage was approximately 129,000.
The worst 2011 Mercedes-Benz ML350 problems
Ranked by number of owner complaints. Mileage and cost come from what owners wrote.
Problems by type
Tap a problem to see which part fails, at what mileage and in which other years.
- Airbags59
- Brakes19
- Electrical16
- Engine7
- Transmission7
- Acceleration3
- Lights3
- Seats3
- Body2
- Fuel system2
- Driver assistance1
- Seat belts1
- Tires1
Specific symptoms reported on the 2011 Mercedes-Benz ML350
Recalls 3
Service brakes, hydraulic: power assist: vacuum
- What is wrong
- Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2006-2012 ML, GL, and R-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. Moisture may accumulate and cause corrosion in the brake booster housing unit, which can result in reduced brake performance or brake failure.
- Risk
- Reduced brake performance or brake failure can increase the risk of a crash.
- Remedy
- Owners are advised not to drive their vehicles until the remedy has been performed. Dealers will remove the rubber sleeve, inspect the brake booster, and as necessary, replace the brake booster. All repairs will be performed free of charge. Owner notification letters were mailed on May 24, 2024. Owners may contact MBUSA customer service at 1‑800‑367‑6372. MMUSA's number for this recall is 2024050001/2. This recall is an expansion of previous recall number 22V‑315.
Recall number 24V298000 · Recall details
Service brakes, hydraulic: power assist: vacuum
- What is wrong
- Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2006-2012 ML-Class, GL-Class, and R-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. Moisture may accumulate and cause corrosion in the brake booster housing unit, which can result in reduced brake performance or brake failure.
- Risk
- Reduced brake performance or brake failure can increase the risk of a crash.
- Remedy
- Owners are advised not to drive their vehicles until the remedy has been performed. Dealers will remove the rubber sleeve, inspect the brake booster, and as necessary, replace the brake booster. All repairs will be performed free of charge. Owner notification letters were mailed June 30, 2022. Owners may contact MBUSA customer service at 1‑800‑367‑6372. MBUSA's numbers for this recall are 2022050014, 2022050015 2022090006, & 2022090007.
Recall number 22V315000 · Recall details
Air bags: frontal: driver side: inflator module
- What is wrong
- Mercedes-Benz USA, LLC. (MBUSA) is recalling certain model year 2009-2010 ML320 BlueTec 4Matic, GL320 BlueTec 4Matic and R320 CDI 4Matic, 2011 E350 Cabriolet and E550 Cabriolet, 2009-2011 ML350, ML350 4Matic, ML550 4Matic, ML63 AMG, and C63 AMG, 2010-2011 ML450 4Matic Hybrid, E350 Coupe, E350 4Matic, E550 Coupe, E550 4Matic, and E63 AMG, 2011-2012 GL350 BlueTec 4Matic and R350 BlueTec 4Matic, 2009-2012 GL450 4Matic, GL550 4Matic and R350 4Matic, 2007-2008 SLK280, SLK350, and SLK55 AMG, 2011-2014 SLS AMG Coupe, 2012 SLS AMG Cabriolet, 2013-2014 SLS AMG GT and SLS AMG GT Cabriolet, 2005 C230 Kompressor and C320, 2006-2007 C230, 2006-2011 C350, 2008-2011 C300 and C300 4Matic, 2010-2012 GLK350 and GLK350 4Matic and 2007-2008 Chrysler Crossfire vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to rupture.
- Risk
- In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
- Remedy
- MBUSA will their notify owners, and Fiat Chrysler will notify the affected Chrysler owners. Dealers for the respective brands will replace the driver's frontal air bag module, free of charge. This recall began November 2016. Mercedes-Benz owners may contact MBUSA customer service at 1‑800‑367‑6372 and Chrysler owners may contact Fiat Chrysler customer service at 1‑800‑853‑1403.
Recall number 16V081000 · Recall details
See all 3 recalls for the 2011 Mercedes-Benz ML350
Defect investigations
Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
EA21002
Technical service bulletins for the 2011 Mercedes-Benz ML350 108
Bulletins tell dealers how to fix known problems. A warranty extension means the manufacturer pays for that repair for longer.
- Mercedes-Benz USA, LLC will provide an Extended Modification Warranty for each vehicle that has received...
- Repeat workshop visit for vehicle vibration while braking from 60MPH. NOTE: Although the symptom is...
- Clanking noise from the area of the speakers in the doors
- During part of the steering movement, it feels heavier or more difficult to steer in the same spot every time
- Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end)
- Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements...
- After successful commissioning of the HERMES control unit (N112/9) with XENTRY Diagnosis DVD 03/2026, the...
- The sliding sunroof glass panel of the panoramic roof reverses during the closing process, either once or...
- Headlamp, front fog lamp leaky or fogged
- Headlamp, front fog lamp leaky or fogged
What 2011 Mercedes-Benz ML350 owners say
Most recent owner complaints, unedited.
The contact owns a 2011 Mercedes-Benz ML350. The contact stated that while driving approximately 60–65 MPH, the brake pedal was depressed and the vehicle started sliding. The contact stated that the vehicle stalled. The brake warning light was illuminated. The vehicle was towed to a tow lot. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 88,000.
The contact owns a 2011 Mercedes-Benz ML350. The contact stated that while the vehicle was parked and turned off, there was brake fluid leaking from the vehicle with the BRAKE warning light illuminated. The dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was not available.
The contact owns a 2011 Mercedes-Benz ML350. While the daughter was driving at an unknown speed, several unknown warning lights illuminated on the instrument cluster. The driver heard an abnormal hissing or squeaking sound while depressing the brake pedal. The vehicle was driven back to the residence. The contact’s son then drove the vehicle to a shopping center, and when the brake pedal was depressed, the brake warning light illuminated, and the vehicle unexpectedly entered SAFE Mode. The contact was unable to shift to drive(D). The brake pedal was depressed and went to the floorboard. The vehicle was towed to a dealer. The vehicle was not yet diagnosed or repaired. The contact stated that the vehicle was repaired under the federal safety agency Campaign Number: 22V315000 (Service Brakes, Hydraulic). The contact stated that the dealer had inspected the brake booster, but no parts were replaced. The contact related the brake failure to the recall. The manufacturer was informed of the failure. The failure mileage was approximately 111,000.
Corroded brake lines. This is a well known issue for many ML350s built during this time period. This car was built with steel brake lines that easily corrode and present a serious safety issue. While driving a few months ago, the car suddenly lost the ability to brake because a line rusted completely through. The mechanic noted the lines are rusted in many other places as well. Mercedes refuses to correct this under warranty.
ABS Pump defective. Dealer refuses to replace this safety item.
I believe the electrical system may be defective as ever since I have had it the light bulbs frequently have to be changed. We own three vehicles in my households (the other 2 are non-Mercedes) and none of my other vehicles do this. The latest issue with the electrical system is that the rear tail lamp and power lift gate. I was told there was water that was getting in from somewhere but mechanic could not find where. I need a new SAM module and that is why my power lift gate motor does not work. As I did some research online, the same exact problem was recalled on a the same model but the 2009 model and I have the 2011 model. I believe my car should be part of the same recall which I believe is Mercedes recall number 2009030003. That appears to be a faulty seal around the rear tail lamp assembly. I believe this is a manufacturer's defect that should be covered and would likely explain why I have had to change out light bulbs so many times over the years.
I was driving locally and when I put on the brakes for a car exiting a street. Immediately my car sensor went on and my car brakes started to fail. It was a very scary situation. This is a known problem with Mercedes. Mercedes has a recall for the brake booster but will not fix the booster without the brake like being fixed. I have reached out to foreign motor car dealerships and this issue with the brake line is a known problem and a safety issue but Mercedes is not taking responsibility for this issue that can kill someone for their parts that are corroding and rotting. Mercedes too years to take responsibility for the brake booster which can kill people and now they are not taking responsibility for their brake line issues that again can injure and kill people.
an Exhaust recycle hose cracked; causing cabin to fill with carbon dioxide. Driver, (me) became disorented.. ran off right shoulder, ran into center divider cement, before rearending truck. Engine light later came on indicating (HVOC?) ERROR Mechanic was able to locate leak and repair. Vehicle now performing properly. A DEFECT THAT ALLOWS CARBON DIOXIDE INTO THE PASSENGER CABIN, IS A SERIOUS AND LIFE THREATENING SITUATION.
My vehicle jerks back and forth at low acceleration, and it often goes into limp mode which makes the vehicle only drive at around 20 mph at most. I was on the highway, when this happened. I have a 722.9 transmission, and this is a common problem. Why is the snapping recalled? I have had a checked with Mercedes-Benz of music City when I had gotten my recall work done, and they said that it just needs a whole new transmission. They said that they had never seen an issue like this. They want $16,000. I have been reading and reading and reading I don't know how they have not seen the issue when it's very very common. Again my question is, why has this not been recalled? There are soldering issues for a speed solenoid sensor, and the TCU it makes it go bad. What is going on, and why has this issue not been addressed? I have two toddlers that I drive in my vehicle every single day. God forbid we're not so lucky next time. The only reason why we did not get hit this time, is because we were on the highway at a slow hour of the day. My son is disabled and we are on the highway and in the car a whole lot. If this happens during rush hour, we will be no doubt smacked into by another vehicle.
Compare the 2011 Mercedes-Benz ML350
Other model years
Questions about the 2011 Mercedes-Benz ML350
Is the 2011 Mercedes-Benz ML350 reliable?
Owners have filed 111 complaints about the 2011 Mercedes-Benz ML350, 1.6 times a typical ML350 model year.
What is the 2011 Mercedes-Benz ML350 year score?
The 2011 Mercedes-Benz ML350 scores 56 out of 100 (below average). The score compares it with the other model years of the Mercedes-Benz ML350: 75 is a typical year, 50 means twice the usual complaints, and serious complaints and recalls lower it.
What is the most common problem with the 2011 Mercedes-Benz ML350?
Airbags, with 59 complaints, typically around 61,000 miles. Next is brakes (19).
How many recalls does the 2011 Mercedes-Benz ML350 have?
3 recalls, covering service brakes, hydraulic and air bags.
Was there a recall on the 2011 Mercedes-Benz ML350 airbags?
Yes, 1 recall: 16V081000. Check your VIN to see if your car still needs the free repair.
What year does the Mercedes-Benz ML350 have bad airbags?
The Mercedes-Benz ML350 model years with the most airbags complaints are 2010 (67 complaints) and 2011 (59 complaints).
VIN decoder
See the problems and recalls for an exact car
Buying a used 2011 Mercedes-Benz ML350?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history