2005 Volvo VN problems

What is wrong

Volvo is recalling certain model year 2002-2013 VHD and VN trucks, manufactured from August 4, 2000, through June 22, 2012, and equipped with bench passenger seats. The seat belt d-ring weld may not be sufficient enough to meet the seat belt pull test. Therefore, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard No. 210, "Seat Belt Assembly Anchorages."

Risk

In the event of a crash, an insufficient seat belt weld may prevent the seat belt from properly restraining the occupant. This increases the risk of injury to the seat occupant.

Remedy

Volvo Trucks of America will notify owners, and dealers will replace the suspected d-ring, free of change. The safety recall began on May 10, 2013. Owners may contact Volvo at 1‑336‑393‑2000.

Recall number 12V510000 · Recall details

What is wrong

On certain heavy duty class 8 trucks, equipped with holland air suspension systems, a transverse beam casting may fracture under normal loads. If a casting breaks when the vehicle is traveling on a roadway there is the potential for pieces of the casting to become projectiles and the suspension?s transverse beam may drop down low enough to contact the road surface.

Risk

This will cause sparks that could potentially ignite and cause a fire.

Remedy

Dealers will inspect and replace the defective transverse beam assemblies. The recall began on august 26, 2005. Owners may contact volvo trucks at 1‑800‑528‑6586.

Recall number 05V311000 · Recall details

ODI opened Recall Query RQ11-001 after a review of EWR Field Reports identified lower bunk window separations on the subject vehicles.Volvo had issued three recalls for sleeper window separations since 2003.Additionally, Volvo had issued two bulletins for sleeper window issues during the same time period.The frequency of related actions led ODI to open this formal investigation.An Information Request (IR) letter was sent to Volvo on 23 June 2011.Volvo responded on 17 August 2011 and then provided updated warranty information on 9 January 2012.Volvo provided production change data and warranty information which was correlated to vehicle build month and failure date.ODI analyzed the data to determine if additional production time frames should have been included in previous recalls.ODI also requested information from its network of fleet owners.The response from this network reaffirmed the accuracy of the updated warranty information.Based on the information and data received, ODI has concluded that all production periods have been appropriately addressed by Volvo's previous recalls and no additional recall action is required at this time.

RQ11001

EA09-003 is closed with the submission of Volvo's recall 10V‑282 recalling approximately 111,034 Model Year (MY) 1998 through 2005 VN and VNL class 8 trucks.Volvo announced recall 10V‑282 in response to the federal safety agency's recall request letter dated June 3, 2010 (available at the federal safety agency's web site . the federal safety agency found that these vehicles were designed and manufactured with a TRW ball joint that does not meet the combined performance requirements and foreseeable inspection practices of the U.S. market.The ball joint in the steering system that connects the driver's side steering arm/knuckle to the drag link can fail resulting in a total loss of steering on the vehicle.Volvo changed the size and supplier of the ball joint used on these vehicles starting with the 2006 MY vehicles.The failure rates on the vehicles manufactured with the larger ball joint are significantly less than the subject vehicles.The closing of this investigation does not constitute a finding by ODI that no safety defect exists in the vehicles that are not included in Volvo's recall.ODI will continue to monitor the incidence of drag link failures in other MY Volvo trucks.Note:The recall request letter dated June 3, 2010 associated with this investigation describes 49 incidents of ball joint separation.After a comprehensive review of the data it was discovered that the number of separations that the federal safety agency was aware of was 41 with a failure rate of 36.9 R/100K.The 41 separations resulted in 23 crash allegations.

EA09003

Odi has decided to upgrade this pe and conduct field work and testing.summary numbers in this resume are represenative of only the 2005 model year vehicles. See the attached report for details.

PE08053