1995 Ford Taurus problems

Filed Jun 19, 2017 · Steering, Suspension · 136,000 miles · MO

This past sunday, on june 11, 2017 I was driving home from a graduation party and there was a loud "pow" once I accelerated from a stop. My steering was very stiff (as if I was driving an ancient large truck with no power steering, also my exhaust system at least partially came undun. I was able to get the crippled car to our regular repair shop, who told me that I had a subframe rust-collapse. I had talked to a shadetree mechanic friend, who said that it wasn't an actual subframe collapse, but the next layer up, the engine cradle whose sleeves are no thicker steel than the unibody sheetmetal. One of the sleeves rusted through. Supposedly the engine cradle sleeves are removable/or the cradle itself. My mechanic friend and the tow fellow that brought my car back to my home, both said that what happened is quite rare, they never heard of such an incident. The cradle rust through caused my front subframe to partially collapse and the engine is tilted down on the right-front. This disconnected the exhaust and bound-up my rack-and-pinion steering, rendering the car unsafe to drive. This car is not a rust-bucket, no rusty body panel holes, and everything else still works! Just the paint and clearcoat are flaking-off. I have looked on the internet and searched local salvage yards, but cannot find a good engine cradle/sleeves. Yet, there are scads of good taurus engines cheaply available. Why didn't ford offer replacement engine cradle/sleeves? Was there no recall? I'd bet I'm not the only person this happened to!! I would like to get this car fixed! I have photos of the subframe fallen after the engine cradle failure. Please send me an e-mail address I can upload them to. I lose this page if I try to upload here (4th time!)

Filed Dec 19, 2015 · Body, Engine · MN

Sub frame.

Filed Jul 13, 2015 · Body · 239,000 miles · IN

Tl* the contact owns a 1995 ford taurus. The contact stated that the front subframe mounted bolts fractured when driving over an unleveled road. In addition, the contact stated that the subframe, the front mount bolts, the reinforcement plates, and the engine cradle fractured causing the vehicle to be unable to be driven. The vehicle was not included in the federal safety agency campaign number: 98v323000 (structure). The vehicle was not diagnosed or repaired. The approximate failure mileage was 239,000.

Filed Jul 27, 2014 · Brakes · 92,241 miles · OH

Brake lines at the front driver side wall from the ABS pump rusted through during vehicle operation causing loss of fluid and ability to safely stop the vehicle.

Filed Mar 19, 2014 · Engine, Steering · 184,568 miles · MO

I was driving along when all of a sudden a big bang car slammed pavement began to swerve. Started smoking off burned rubber tire popped an car was broke down wheel dangling.

Filed Sep 13, 2013 · Acceleration · 111,000 miles · TN

Tl* the contact owns a 1995 ford taurus. The contact stated that while reversing from a parking space, the power steering failed and the steering wheel seized. The vehicle was taken to an independent mechanic where it was stated that the under carriage needed to be replaced. The vehicle was not repaired and the manufacturer was notified. The approximate failure mileage was 111,000.

Filed Sep 13, 2013 · Steering · 111,000 miles · TN

Tl*the contact owns a 1995 ford taurus. The contact stated that while reversing from a parking space, the steering wheel seized. The vehicle was taken to an independent mechanic where it was advised that the under carriage needed to be replaced. The vehicle was not repaired and the manufacturer was notified of the failure. The approximate failure mileage was 111,000.

Filed Jun 23, 2013 · Body · 135,267 miles · TX

My 1995 taurus experienced a failure of the lower sub-frame mount retainer plate. The retainer plate had become severely corroded over time and this corrosion had weakened the retainer plate enough to allow the bolt head to pull through the retainer plate. This failure was caused by long term exposure to moisture from normal precipitation and consistent with the failure detailed in the reasons for recall section of service recall bulletin 98s36. The ford recall bulletin states the retaining plate nut becomes severely corroded from long term exposure to road salts and retention of moisture in the mounts. Due to corrosion, my 1995 taurus experienced that same failure but the corrosion was not caused by road salts. Although this failure occurred at slow speed, steering was affected. Had this failure occurred at high-speed or while crossing a slight bump or dip in road surface, steering could have become difficult, potentially leading to an accident. This is a cause of concern for other 1986-1995 taurus and sable vehicles still in service. Because my vehicle had not been registered in any of the states included in the recall, my request to ford motor company to include my vehicle in the recall was denied. The federal safety agency recall 98v323000 was designed to prevent this type of failure from occurring. Had this vehicle been included in this safety recall, this failure would not have occurred. It is clear that this failure is also caused by corrosion due to long term exposure to moisture from normal precipitation and not exclusive to road salts. Thus, the federal safety agency campaign id 98v323000 should not be limited to only states where road salts are used. Therefore, I am requesting ford motor company be required to expand the federal safety agency campaign id 98v323000 to cover vehicles registered in states where long term exposure to moisture from normal precipitation is a factor.

Filed May 15, 2013 · Acceleration, Electrical · 123,000 miles · SC

Arriving home, I parked the car in our attached garage. I went into the garage and I noticed the smell of something hot or shorted coming from the engine compartment. I backed the car out of the garage and disconnected the battery. The next day, I reconnected the battery and no longer noticed the smell. I drove it and there was no more odor. The speed control failed to operate, and the speed control deactivation switch was leaking brake fluid on the wiring harness and the 3 amp fuse in the wirng harness was blown, but only after coming close to starting a fire. Ford has a history of safety problems with the speed control deactivation switch leaking brake fluid on the wiring harness and causing fires. This car was recalled in 2007 to install a fused wiring harness with a 3 amp fuse between the switch and the speed control servo where it offered no protection. The car was recalled again in 2008 to replace the first wiring harness with one having the fuse ahead of the deactivation switch. The 3 amp fuse in series with the 15 amp fuse is far less likely to cause a fire than having only the 15 amp fuse. Nevertheless, I came close to having a major fire in our home while we were inside had I not noticed the problem. The 3 amp fuse did its job, but there was enough brake fluid and heat to possibly cause a fire. I took the car to the dealer and they replaced the leaking switch and the fused wiring harness. They charged me $177.03 for the repair. Ford has recalled about 10 million vehicles to add the fuse, but I am convinced that the design is still unsafe because 3 amps could still ignite brake fluid, I hope this note may save others from serious problems, as more of these pressure switches will fail with age and leak brake fluid on the continuously energized wiring harness. The 3 amp fuses may not always blow soon enough.

Filed Sep 17, 2012 · Electrical, Engine · 19,000 miles · CA · fire

Tl* the contact owns a 1995 ford taurus. The contact stated that while traveling 65 MPH, flames emitted from the hood, covering the windshield. The coolant warning light illuminated prior to the failure. The vehicle was towed to a private mechanic who confirmed hat the radiator and electronic wiring harness needed to be replaced. The manufacturer was not contacted. The vehicle was not repaired and the VIN was unknown. The failure and current mileages were 19,000.