2018 Ram 2500: ball joint or control arm failure

Filed Jun 16, 2026 · Steering · LA

The truck started with a death wobble in the steering. Ball joints,bushing,stabilizer bar replaced front end work was done. Brought to the dealership approx 4 times for the same steering problem. It still has a small wobble pulling to the Rt or left. Steering was very loose but has been tightened up with a replaced steering shock. But the steering wobble continues had the steering gear box replaced twice. Dealership does not know how to fix the problem.

Filed Sep 11, 2025 · Steering · LA

Truck was "repaired" under Recall V06. Drag link/track bar was welded in place, which was supposed to be a temporary fix until parts became available to replace the bad drag link. In Mar of this year, I had the ball joints replaced. Upon repair, my steering wheel was cocked to the left in order to drive straight. Brought the truck back to have that repaired. Service center told me that because the part had been welded, they would have to break the weld, center the steering wheel, and reweld the part. That took place but did not fix the problem. My truck still turns right when the steering wheel is level. I have since been caught between Ram Customer Care and the dealership with each telling me the other needs to "do something" and both referring me to the other for assistance. I have attached photos of the work done and a copy of the recall. The weld job done on my truck is horrible, if not unsafe. But, I have to drive my truck. I think Ram is taking advantage of the good faith the Administration has shown them by allowing them to decide whether to make the replacement of the part. It should be mandatory. Probably thousands of Ram trucks in a similar situation on America's roads. The welded adjustment sleeve makes a proper alignment of the steering wheel impossible. The alignment is designed to be adjusted. Finally, I noted that the dealership violated the "do not sell" of the recall. I bought the truck in March 2019, without the recall call work done - unbeknownst to me. They did not take the recall seriously.

Filed Sep 10, 2024 · Steering, Wheels · OH

I received the recall notice V06, for the Drag Link, I purchase 4 new tires and took the truck in to have the repairs done, the dealership informed me that I also needed upper and lower ball joints both sides and front end alignment, I had them preform all that they said it needed. I took the truck back because I noticed excessive tire were and they told me that the Drag link needs replaced, the alignment redone and that I would have to pay for it

Filed Jul 19, 2024 · NM

Vehicle has massive sway when carrying payload in bed of truck. Not a problem pulling trailor with a load just when loaded in bed. Is not the death wobble associated with Dodge pickups have had checked by local mechanic and no problems found on suspension, swaybars, shocks, springs, ball joints or other issues. Is available for inspection. 1st time it happened was carrying a ton of pellets. occurs around 45-50 mph and is very dangerous on uneven pavement only way to stop it is to slow down. no warning lamps or messages. has happened 4-5 times but only with a load in bed of truck. need an email address to upload videos of problem

Filed Oct 9, 2022 · Steering, Suspension · KS

On 10/07/2022, I took the vehicle VIN number in reference for tire change at FIRESTONE Auto Care (440 S. Main St., Wichita, KS 67202-3720 - [316] 265-6659]). I also requested, wheels alignment and wheels/tire balance, and brake inspection. Upon those inspections, the technicians pointed out an IMPORTANT issue as follows: "IMPORTANT: This vehicle may be subject to a recall involving the toe adjuster. Search the internet for 'recall number 19V‑021' for the latest information Under no circumstances should a weld from a recall repair be removed for any reason, including to perform an alignment. Removing the weld would remove a safety recall remedy that is currently in place., which would cause a serious vehicle safety issue. To adjust toe on a vehicle with a welded drag link in the WinToe procedure, choose 'select steering type' on the second tier of 'k-keys. Then, select the 'one tie rod' option. For more information, please reference TSB 19-001-19." The vehicle in reference has been mostly serviced at Davis-Moore (7675 E. Kellogg, Wichita, KS 67207 [316] 618-2268). This is the first time I took this vehicle to FIRESTONE who pointed out the above information. Please, let me know if this is a safety issue and, if it is, please take the necessary steps to enforce a solution to that issue. Thank you.