Break actuator, 2nd event event 1 complaint number 11234969 23 july 2019, dropped my car off with toyota clovis same dealership (jacob was my rep) because my brakes was making the creaking sound/thumping. I asked him to check my brakes and if that wasn't the problem, call me to let me know what the problem was. He called me later that day and said it was the brakes, they went ahead and changed the brake pads. He said they recommend to change brake actuator fluid? Since it wasn't done when they changed the actuator previously and he was going to charge me. I commented that it should have been done back in 2017 when the brake actuator originally failed. I asked if it would affect my car, drivability, etc. And jacob said no it should drive fine with no problems other than a few settle sounds. He said but the brakes are fixed and it's no longer making the sound/ thumping. So I declined the fluid service. 25 july 2019, I was going to get my daughter from school. By then, it had started to make the cheaking noise/thumping. I got just about to her summer school (on fowler ave) and all of the lights on my panel lit up again. I pulled over and called my husband. I drove it home slow. We called toyota, spoke to the manager, explained that this had happened before. I just paid them $240 for brake pads that I didn't need. I refused to drive the car. The dealership was closing in 1.5hrs which left no time for tow truck. My husband drove it to the dealership, I followed in his car. Toyota (jacob) gave me a loaner. 25 july 2019, the manager called and said the issue was the brake actuator failed again but because the part which is obviously a defective (manager actually agreed) was only covered for a year, I'd have to contact corporate to see if they could change it out at no cost. I will call tomorrow (26 july 2019)...although, I do not plan on ever driving this car again.
The worst 2010 Toyota Camry Hybrid problems
Ranked by number of owner complaints. Mileage and cost come from what owners wrote.
- Brakes5
- Body2
- Engine2
- Airbags1
- Electrical1
Problems by type
Tap a problem to see which part fails, at what mileage and in which other years.
- Brakes5
- Body2
- Engine2
- Airbags1
- Electrical1
- Wheels1
Recalls 2
Air bags: frontal: sensor/control module-inactive
- What is wrong
- Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
- Risk
- If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
- Remedy
- Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1‑800‑301‑6859.
Recall number 13V014000 · Recall details
Vehicle speed control: accelerator pedal
- What is wrong
- Toyota is recalling certain model year 2004-2010 passenger vehicles. The accelerator pedal can get stuck in the wide open position due to its being trapped by an unsecured or incompatible driver's floor mat.
- Risk
- A stuck open accelerator pedal may result in very high vehicle speeds and make it difficult to stop the vehicle, which could cause a crash, serious injury or death.
- Remedy
- Toyota filed an amended defect report on november 25, 2009, stating that dealers will modify the accelerator pedal and, on certain vehicles, alter the shape of the floor surface under the pedal. These changes address the risk of pedal entrapment due to interference with the floor mat. Redesigned accelerator pedals will become available beginning in april 2010 and dealers will replace any modified pedal with the new pedal if desired. Also, dealers will replace any genuine toyota or lexus all-weather floor mats with redesigned all-weather mats, or repurchase the previous mats from owners who do not want the new ones. Additionally, software modifications will be installed on camry, avalon and lexus es 350, is 350 and is 250 models that will ensure that the brake overrides the accelerator in the event both brake and accelerator pedals are applied. Toyota will begin mailing letters to owners on december 31, 2009. Owners may contact toyota at 1‑800‑331‑4331, lexus at 1‑800‑255‑3987.
Recall number 09V388000 · Recall details
See all 2 recalls for the 2010 Toyota Camry Hybrid
Defect investigations
Pedestrian alert sounds
the federal safety agency received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, the federal safety agency opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified the federal safety agency he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by the federal safety agency regarding the subject matter of the petition.
DP22005
Brake Actuator malfunction
On June 25, 2014, Toyota initiated a Warranty Enhancement Program (ZE1) to extend warranty coverage for the brake actuator assembly and skid control ECU/brake pedal stroke sensor in certain MY 2007 to 2011 Toyota Camry hybrid vehicles. Toyota's program covers repairs related to two conditions:internal malfunctions of the Brake Actuator assembly; and overly sensitive monitoring logic for the Brake Pedal Stroke Sensor.Primary coverage provides warranty enhancement until November 30, 2015, with no mileage limitation.After the primary coverage period ends, secondary coverage is provided for 10 years or 150,000 miles from the date of first use, whichever occurs first.In addition, on July 10, 2014, Toyota initiated Limited Service Campaign E0U to replace the Brake Reservoir Tank in MY 2007 through 2011 Toyota Camry hybrid vehicles.The LSC will be available until June 30, 2017, and will only be available at an authorized Toyota dealer.ODI's analysis of failure data determined that the majority of records were related to the Brake Actuator condition, which appeared to be the causal component in 734 complaints/field reports and 864 warranty claims.The Brake Pedal Stroke Sensor (80 reports/189 claims) and Brake Reservoir Tank (91 reports/44 claims) conditions were identified in far fewer records.Analysis of the failure data indicate that each condition provides warning prior to any reduction in power assisted braking, with less than 10 percent of all reports and claims involving diagnostic codes or complaint narratives indicating increased braking effort or reduced brake effectiveness.In addition, most of the incidents in which reduced braking assist appears to have occurred involved operation in a reduced assist mode and not a sudden, complete loss of power assisted braking.ODI assessed reduced assist mode in a subjective driving evaluation which indicated that the brake system provided normal and harddeceleration capability with reasonable increases in pedal effort.Less than one percent of reports and claims analyzed by ODI included evidence indicating a complete loss of power assisted braking occurred and this mode requires operation for a significant period of time with multiple audible and visual warnings.Repair expense was cited in many of the complaints reviewed by ODI, especially those related to the Brake Actuator, which had repair costs exceeding $3,000 according to some complaints.High repair cost appears to have been a factor in the only crash identified by ODI for the fault conditions identified by Toyota, which involved a Brake Actuator failure that was diagnosed but the owner declined repair approximately eight months prior to the reported crash incident.This preliminary evaluation is closed.The closing of this investigation does not constitute a finding that a safety-related defect does not exist.For additional information regarding this investigation, including analysis of the Brake Actuator, Brake Pedal Stroke Sensor, and Brake Reservoir Tank fault conditions and failure experience, see Attachment A to this closing resume.
PE14001
Technical service bulletins for the 2010 Toyota Camry Hybrid 282
Bulletins tell dealers how to fix known problems. A warranty extension means the manufacturer pays for that repair for longer.
- Obsolete notice
- This bulletin includes basic procedures for performing a rescue charge on Ni-MH high voltage (HV) batteries
- Condition in which a musty odor is present
- Acid rain results from rainwater or other airborne moisture that become acidic due to industrial chemical...
- To prevent brake rotor rust from forming during transportation and storage, wheel film will be used...
- The condition known as acid rain is caused by airborne chemicals or particles in the atmosphere, which mix...
- Toyota vehicles are currently protected with RapgardTM protective film designed to protect the horizontal...
- Vehicles may occasionally be subjected to contamination by airborne iron particles shed from railroad...
- Condition in which a musty odor is present
- This Service Bulletin provides updated non-electric water pump leak inspection and diagnostic tips for...
2010 Toyota Camry Hybrid fuel economy
Official EPA estimates in miles per gallon (MPGe for electric). Ranges cover trims that share the same engine.
| Engine | Drive | City | Highway | Combined |
|---|---|---|---|---|
| 2.4L 4‑cyl Hybrid | FWD | 33 | 34 | 34 |
What 2010 Toyota Camry Hybrid owners say
Most recent owner complaints, unedited.
Brake actuator: my brakes were making a creaking noise /thumping when pressed...in which case I thought it was just time for regular maintenance. About 0430, december 21, 2017 (my wedding anniversary) I was driving on the highway 99south headed from fresno, ca to tulare, ca...about a 45min drive. While on the highway, my car started to make random chiming sounds that did not seem to come from anywhere particular. There was no indicator light associated with the sound...it was just random sounds I had never heard before. That went on periodically for the next 20-30mins. I finally made it to the prosperity ave off-ramp and began to press the breaks. Immediately, all of the lights on my panel lit up and a steady, high pitch sound came on and I couldn't stop my car. I panicked, continuously trying to break pushing hard as I can. I ended up being able to lead it off the exit and into a popeyes parking lot next to the off-ramp where it eventually came to a stop. Thank the lord that no one was on the road that early in the morning. The car was towed from tulare back to fresno (toyota corporate office would not refund that 200 bucks). Toyota dealership said it was the break actuator, it was a "warranty" that they'd cover at no cost. I asked why I wasn't notified since the situation is life threatening and there were no answers for that. Toyota had my car for about a month because I demanded they repair everything associated with the breaks...quite honestly I was just afraid to drive the car. Eventually, I drove it again with my anxiety gradually diminishing...but by no means gone. I visited a mental health doctor to help, although it didn't. 23 july 2019, it went out again. Will post that event on separate entry.
The ABS brake actuator on my toyota camry hybrid has gone bad causing my vehicle to be unsafe for operation. I was initially told that the actuator would be covered under a warranty extension. However after further inspection, I was told that it would not be covered because there isn't any warning lights on the dashboard and/or no error codes present when hooked up to a scan tool even though the part is faulty and needs to be replaced.
Lug nuts swelling making it impossible to remove with supplied lug wrench. All 20 lug nuts show evidence of separation of the steel nut and the decorative chrome cover covering the steel lug nut. Defect was found by tire dealer during purchase of new tires when the technician had difficulty removing lug nuts. According to the tire store manager this damage is caused by water getting between the steel nut and the decorative cap which causes rust to form. When the oxidation forms it puts pressure on the decorative cap causing it to expand. The normal 21mm wrench will not fit over the lug nut due to the expansion so the next size wrench is necessary which then damages the nut. The normal lug nut wrench supplied by the manufacturer for the car is therefore not able to be used to remove lug nuts. I have the damaged lug nuts if needed for examination
Excessive oil consumption
Excessive oil consumption at a rate of 4 quarts every 3000 miles.
Tl* the contact owns a 2010 toyota camry hybrid. While driving approximately 40 MPH and attempting to engage the brakes, the brakes malfunctioned causing the vehicle to crash into the rear of a second vehicle. While depressing the brake pedal, the vehicle slowed down but did not respond normally. The air bags failed to deploy. No injuries were reported and a police report was not filed. The cause of the failure was not diagnosed. The manufacturer was not notified. The failure mileage was 71,350.
Three of the four door lock actuators have failed. The failures begin intermittently and then result in total failure. The front driver side door and rear driver side door have totally failed. The rear passenger door now intermittently fails. Toyota indicated that they have no recalls or extended warranties. Internet searches show that multiple toyota models have this as a common failure. This poses a significant safety issue as the door locks do not respond to the electrical unlock / lock button and do not respond to the remote. Manual unlock still works; however, in the case of small children or use of the child safety locks, this will likely not be an option. I have registered a complaint case with toyota USA. Toyota USA indicated that nothing will be done by them at this time. They will notify me if they issue a recall or extended warranty in the future.
The dashboard on my 2010 toyota camry hybrid is melting and sticky to the touch.
I have noticed lately that when I depress my brake pedal, it starts to slow the car down, but suddenly disengages and I have to depress much harder. It's almost like the brakes let go. I know there is an issue with earlier models and their brakes, is it possible it would extend to 2012 camry hybrids?
Compare the 2010 Toyota Camry Hybrid
Camry Hybrid vs Toyota PriusCamry Hybrid vs Ford Fusion HybridCamry Hybrid vs Honda Accord HybridCamry Hybrid vs Honda Insight
Other model years
20062007200820092010201120122013201420152016201720182019202020212022202320252026
Questions about the 2010 Toyota Camry Hybrid
Is the 2010 Toyota Camry Hybrid reliable?
Owners have filed 10 complaints about the 2010 Toyota Camry Hybrid, fewer than a typical Camry Hybrid model year.
What is the 2010 Toyota Camry Hybrid year score?
The 2010 Toyota Camry Hybrid scores 82 out of 100 (good). The score compares it with the other model years of the Toyota Camry Hybrid: 75 is a typical year, 50 means twice the usual complaints, and serious complaints and recalls lower it.
What is the most common problem with the 2010 Toyota Camry Hybrid?
Brakes, with 5 complaints. Next is body (2).
How many recalls does the 2010 Toyota Camry Hybrid have?
2 recalls, covering air bags and vehicle speed control.
What year does the Toyota Camry Hybrid have bad brakes?
The Toyota Camry Hybrid model years with the most brakes complaints are 2007 (423 complaints), 2008 (67 complaints) and 2009 (59 complaints).
Is there a class action lawsuit over the Toyota Camry Hybrid?
Yes. Camry Hybrid inverter recall lawsuit lands in federal court after owner says his new car sat at the dealer for six months (November 12, 2026).
What gas mileage does the 2010 Toyota Camry Hybrid get?
Official estimates for the 2010 Toyota Camry Hybrid range from 34 mpg combined. The most efficient version (2.4L 4-cyl hybrid, FWD) gets 33 city and 34 highway.
VIN decoder
See the problems and recalls for an exact car
Buying a used 2010 Toyota Camry Hybrid?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its historyToyota Camry Hybrid in the news
- Camry Hybrid inverter recall lawsuit lands in federal court after owner says his new car sat at the dealer for six months
- Toyota extends warranty coverage on 2018-2021 Camry, 2020-2021 Corolla and 2019-2021 RAV4 and other models (engine)
- Toyota recalls 2025-2026 Camry Hybrid over instrument cluster/panel problem (508,354 vehicles)