The contact owns a 2009 Ford Fusion. The contact stated that while driving 20 MPH and coming to a complete stop at a traffic light, the brake pedal was depressed but traveled down to the floorboard. The contact shifted into neutral(N) and continued to pump the brake pedal until the vehicle responded. The vehicle was taken to the dealer to be repaired under the federal safety agency Campaign Number: 19V904000 (Service Brakes, Hydraulic). The brake calipers and the brake master cylinder were replaced, and the ABS module was cleaned; however, the failure persisted, and the contact was advised to retrieve the vehicle. The contact believed that the ABS module replacement was required to repair the vehicle, but the dealer denied additional repairs.
2009 Ford Fusion: ABS light or ABS activating
242 of the 1,023 complaints about the 2009 Ford Fusion describe ABS light or ABS activating.
- owner complaints
- 242
- of this car's complaints
- 24%
- typical repair cost reported
- $1,318
- typical mileage
- 103,000
- recalls
- 1
ABS light or ABS activating by model year
What owners say
The braking system failed which was covered by Ford Safety Recall 19S54 with the federal safety agency campaign #19V904000 at 37,750 miles. After research and finding the label of the ABS Hydraulic Control Unit still on the vehicle, being manufactured 07/12/2008, picture attached, it turned out to be the original HCU, whose failures were the reason for the Safety Recall. A Ford dealer had performed software evaluation of the ABS HCU and determined replacement of unit not necessary. This was done on 4/14/2021 at 17,606 miles along with break fluid change to DOT4 and reservoir cap change. Unfortunately my wife just went through a four-way stop intersection when the break pedal went to the end of its movement without being able to stop. No injuries or crashes involved. According to all sources read, this was caused by the ABS HCU valve being stuck open after attempting to brake on the slippery road during rain. The car is no longer safe to drive and sitting in front of our home. Asked Ford Motor Co to take care of this incomplete repair by the Ford dealer and replace the HCU but they say it’s no longer their responsibility. My understanding is that with a safety recall, they are to fix the issue as long as the vehicle is still around. They don’t agree. Can you help with this situation? Thank you! Note: I tried to upload pictures of ABS HCU and VIN labels on vehicle but failed after a number of retry attempts. If you need them I can try another way. Let me know.
The contact owns a 2009 Ford Fusion. The contact stated that the vehicle was taken to an independent mechanic for brake repairs, and after the repairs, the brake pedal felt spongy. The independent mechanic performed further inspections and diagnosed the vehicle with insufficient brake pressure due to a failure of the ABS hydraulic control unit. The manufacturer was notified of the failure. The contact related the failure to the federal safety agency Campaign Number: 19V904000 (Service Brakes, Hydraulic); however, the VIN was not included. The approximate failure mileage was 110,000.
The ABS warning light came on while driving, and the brakes began to feel unsafe during normal stops. I later learned there is an open recall for the ABS module on my vehicle. When I took it to the dealership, they refused to perform the recall repair unless I paid out of pocket for a new ABS control module, even though the recall notice mentions this component. The issue affects braking performance and safety, especially on wet roads. The ABS system continues to malfunction, and the dealership’s refusal to complete the recall repair leaves the vehicle unsafe to drive.
I have recall 19S54 and called Ford. They made an appointment with Downtown Ford, Charleston, WV. The dealership said ford declined my recall repair due to not being able to get their machines to get any codes from my car. The ABS light is on. My mechanic said Ford should fix their recall. The recall says the D03 fluid must be changed to DOT 4 even if no problem found and if problem detected how to fix it! Ford declined because they can't get code reader to work on my car. They said it is a Preexisting Condition! My car is old but only has 24,800 miles and has been kept inside in a heated garage. The Downtown dealership said their hands are tied and would love to make my car safe. Their phone number is 304 344 1601. Please help me get my car fixed!!! I have called Ford multiple times and no help due to not having the codes from the dealership. Thanks!!!!
The contact owns a 2009 Ford Fusion. The contact stated while driving 35-45 MPH, the brake pedal was depressed; however, the vehicle was slow to respond. The check brakes system message was displayed. The ABS warning light was illuminated. The contact received notifications of the federal safety agency Campaign Numbers: 19V904000 (Service Brakes, Hydraulic) and 21V158000 (Air Bags); however, the parts to do the recall repairs were not yet available. The local dealer was contacted. The dealer completed the air bag recall and diagnosed the vehicle and determined that the brake module and HECU module were corroded. The vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue, but no additional assistance was provided. The failure mileage was approximately 96,970. Parts distribution disconnect.
After activation of ABS brake system, brakes became "soft" and "spongy" with permanent increased braking time. As described in safety recall 19S54, this due to to a valve in the Hydraulic Control Unit (HCU) being stuck open. I received a letter from Ford Motor Company regarding this safety recall in 2011 informing of the defect and assuring "we will correct this condition." The vehicle was taken to Koons Ford (1051 E Broad St., Falls Church, VA, 22044; 703‑241‑7250) on 7/5/21 for repair. However, the HCU was not replaced, which appears to be the only remedy to this problem. Instead DOT 3 brake fluid was replaced with DOT 4 fluid, according to Koons Ford. However, after subsequent activation of the ABS brake system, the brakes became impaired again in the same way as before. I returned the car to Koons Ford on [XXX]. A "one-time" repair was performed pursuant to "customer satisfaction program" 21N11, as Ford acknowledged in a letter to dealers dated 12/7/21 that numerous customers were returning as the action prescribed in safety recall 19S54 did not repair the defective brakes. However, the HCU was not replaced. Service Advisor Kevin Lacki told me the HCU "passed" the inspection/diagnostic despite replication of the problem. I complained to Service Manager Rob Ryans who did nothing. I emailed the General Manager of the dealership twice, and he never responded. I called the manufacturer on [XXX] (case #[XXX]), but no action was taken. The problem of "soft" brakes and extended travel time quickly resurfaced and led to a vehicle accident in early 2023. The Ford Motor Company is employing a diagnostic that results in false "passes" for HCUs that should be replaced (and/or this dealership did not correctly perform the service actions). Even after "passing" Ford's diagnostic, the HCU valve(s) become stuck open after ABS activation. The safety recall should be investigated and the recall amended to replace faulty HCUs. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 55
While i was driving and the car hits a hole if the road, and i tried to brake so i can controll the car the breakes became uresponsive for the moment and after a few seconds when i try to brake again the travel space of the brake pedal is increased a lot and is near the end, and it takes a lot before the things return to normal( so it happens only when the car try to activate te ABS system).
Chapman Ford in Marysville, Ohio has had my car for ABS recall for almost a month now. They said they are waiting on the HYDRAULIC CONTROL UNIT HCU. Is this normal to take this long to fix.
Ford dealership refuses to replace ABS HCU unit. Recall states that it will be replaced if defective. Dealership said that it is defective but not part of the recall. Shows that it is part of the recall.
With new brake pads on brake pedal goes to the floor. Brake/ABS is on and won’t clear either. Also when driving brakes want to engage then disengage
The contact owns a 2009 Ford Fusion. The contact received notification of the federal safety agency Campaign Number: 19V904000 (Service Brakes, Hydraulic) however, the part to do the recall repair was unavailable. The dealer had been notified of the issue and confirmed that parts were not yet available. The manufacturer was made aware of the issue. The contact stated that the ABS warning light had illuminated on the instrument panel. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The failure mileage was approximately 43,000. Parts distribution disconnect.
Service bulletins that may apply
- Certain 2006-2010 Model Year Fusion/Milan/MKZ/Zephyr Vehicles Equipped with Anti-Lock Brake Systems DOT 3...
- Some 2008-2017 ford/mercury/lincoln vehicles equipped with sync may generate a vhr that identifies a...
- Ford: if there is an intermittent lack of power, surge, or hesitation while driving the brakes will...
Related recalls
Service brakes, hydraulic: antilock/traction control/electronic limited slip: control unit/module
- What is wrong
- Ford Motor Company (Ford) is recalling certain 2006-2010 Ford Fusion, Mercury Milan, Lincoln Zephyr and MKZ vehicles. The valves within the ABS Hydraulic Control Units (HCU) may react with brake fluids containing specific corrosion preventative additives. This reaction may cause the valves to not close properly.
- Risk
- If the valves do not properly close, additional brake pedal travel may be required to stop the vehicle, increasing the risk of a crash.
- Remedy
- Ford will notify owners, and dealers will flush the brake system with DOT 4 fluid and install a new brake fluid reservoir cap. In addition, the HCU will be tested to detect a possible stuck valve condition, replacing the HCU as necessary. All services will be performed free of charge. The recall began April 1, 2021. Owners may contact Ford customer service at 1‑866‑436‑7332. Ford's number for this recall is 19S54.
Recall number 19V904000 · Recall details
Questions about the 2009 Ford Fusion abs
Is ABS light or ABS activating a common problem on the 2009 Ford Fusion?
242 of 1,023 owner complaints about the 2009 Ford Fusion (24%) mention ABS light or ABS activating. The model year with the most reports is 2010.
How much does it cost to fix ABS light or ABS activating on the 2009 Ford Fusion?
Owners who mentioned a price put the repair at about $1,318 (median of 23 complaints that include a dollar amount). Costs vary with mileage, warranty and where the work is done.
Is there a recall or service bulletin for this on the 2009 Ford Fusion?
There is 1 recall and 4 service bulletins for the same area of the car. Check them below with your VIN.
Other symptoms on the 2009 Ford Fusion
Brake failure 103Spongy pedal 58Door locks 40No deployment 18Check engine light 16Stalling 13Airbag light 9Sudden acceleration 9Engine failure 7Loss of power 7Hesitation 6Grinding brakes 5
VIN decoder
See the problems and recalls for an exact car
Buying a used 2009 Ford Fusion?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history