I am filing this complaint regarding my 2016 Ford Focus S and concerns about a potentially recurring safety defect associated with Ford’s safety recall involving the canister purge valve. My vehicle experienced a no-start condition and stalling. The vehicle became inoperable and had to be towed to an authorized Ford dealership for inspection. These symptoms are particularly concerning because the recall information describes the possibility of engine stalling and difficulty restarting the vehicle. The dealership informed me that the recall had previously been performed on my vehicle. However, despite the recall repair, my vehicle experienced symptoms consistent with those described in the recall. The dealership was able to start the vehicle when it arrived and stated that it could not reproduce the problem. The dealership subsequently performed diagnostic testing on a dyno but claimed that the issue was unrelated to the recall. No definitive cause for the no-start and stalling condition was identified. I was charged $219 for the diagnostic testing. I am concerned that the dealership’s inability to reproduce an intermittent problem does not establish that the underlying safety defect has been corrected or that the current symptoms are unrelated to the recalled component. A vehicle that unexpectedly stalls or fails to restart creates a serious safety risk. If the engine stalls while driving, the driver could lose power and potentially lose power steering assistance and normal brake assistance. The vehicle could become disabled in traffic, at an intersection, or in another dangerous location. A vehicle that unexpectedly fails to restart could also leave the driver stranded in an unsafe location.The problem was intermittent, which may explain why the dealership was unable to reproduce it during its inspection. I am requesting that the federal safety agency investigate whether the recall remedy is adequately addressing this safety concern and reimbursement of a diagnostic and tow fee.
The worst 2016 Ford Focus problems
Ranked by number of owner complaints. Mileage and cost come from what owners wrote.
Problems by type
Tap a problem to see which part fails, at what mileage and in which other years.
- Transmission674
- Engine281
- Fuel system231
- Electrical83
- Steering45
- Acceleration36
- Airbags15
- Wheels15
- Body14
- Driver assistance14
- Brakes13
- Visibility11
- Lights8
- Suspension6
- Seat belts4
- Seats4
- Locks2
- Tires2
Specific symptoms reported on the 2016 Ford Focus
Stalling 242Check engine light 234Shudder 161Jerking 129Hesitation 120Slipping 90Overheating 58Transmission failure 55Engine failure 43Loss of power 41Won't shift 41Won't start 34Grinding brakes 29Fuel pump 20Fuel gauge 19Sudden acceleration 19Misfire 16Power steering loss 16Harsh shifting 14Wipers 13Backup camera 9Headlights 9No deployment 8Knocking 8Steering lock-up 7Adaptive cruise 6Brake failure 6Fire or smoke 5
Trouble codes owners of the 2016 Ford Focus mention
P1450 21P2872 4P07A3 3P090C 3P0106 2P0344 2P0420 2P0507 2P07A5 2P2196 2
Recalls 10
Fuel system, gasoline: storage: evaporative emissions: canister
- What is wrong
- Ford Motor Company (Ford) is recalling certain 2012-2018 Focus vehicles previously repaired incorrectly under recall number 18V735. The Canister Purge Valve (CPV) may malfunction, causing the engine to stall unexpectedly while driving.
- Risk
- An engine that stalls while driving increases the risk of a crash.
- Remedy
- Dealers will update the powertrain control module (PCM) software, free of charge. Owner notification letters were mailed July 29, 2026. Owners may contact Ford customer service at 1‑866‑436‑7332. Ford's number for this recall is 26S40. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on on July 6,2026.
Recall number 26V369000 · Recall details
Power train: manual transmission
- What is wrong
- Ford Motor Company (Ford) is recalling certain 2015-2018 Focus and 2013-2016 Fusion vehicles previously repaired incorrectly under recall numbers 18V169 and 18V845. The clutch may fracture, resulting in damage to the transmission assembly and possibly a transmission fluid leak.
- Risk
- A transmission fluid leak in the presence of an ignition source such as hot engine or exhaust components can increase the risk of a fire.
- Remedy
- Dealers will update the software, free of charge. Additionally, dealers will inspect Focus vehicles and replace the clutch assembly as necessary, free of charge. Owner notification letters were October 16, 2026. Owners may contact Ford customer service at 1‑866‑436‑7332. Ford's number for this recall is 26S43. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on on July 6,2026.
Recall number 26V376000 · Recall details
Equipment: electrical: engine block heater
- What is wrong
- Ford Motor Company (Ford) is recalling certain 2013-2018 Focus, 2013-2019 Escape, and 2015-2016 MKC vehicles equipped with a 2.0L engine. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.
- Risk
- An electrical short circuit can increase the risk of a fire.
- Remedy
- Owners are advised not to plug in their block heater until the vehicle is remedied. Dealers will replace the block heater, free of charge. Owners will also have a alternative option to replace engine block heater element with a threaded plug, and remove the block heater electrical cord. Interim letters, notifying owners of the safety risk, were mailed March 6, 2026. Additional letters will be sent once the final remedy is available. Owners may contact Ford customer service at 1‑866‑436‑7332. Ford's number for this recall is 26S01. Vehicle Identification Numbers (VINs) involved in this recall became searchable on on January 16, 2026.
Recall number 26V011000 · Recall details
Equipment: electrical: engine block heater
- What is wrong
- Ford Motor Company (Ford) is recalling certain 2016-2018 Focus, 2019 Explorer, and 2024 Explorer vehicles. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.
- Risk
- An electrical short circuit can increase the risk of a fire.
- Remedy
- Owners are advised not to plug in their block heater until the vehicle is remedied. Dealers will replace the block heater, free of charge. Owners will also have a alternative option to replace engine block heater element with a threaded blanking plug, and remove the block heater electrical cord. Interim letters, notifying owners of the safety risk, were mailed February 13, 2026. Additional letters will be sent once the final remedy is available, anticipated in December 2026. Owners may contact Ford customer service at 1‑866‑436‑7332. Ford's number for this recall is 25SA4. Vehicle Identification Numbers (VINs) involved in this recall became searchable on on January 16, 2026. This recall expands previous recall number 25V685.
Recall number 26V012000 · Recall details
Engine and engine cooling: engine: oil/lubrication: pump
- What is wrong
- Ford Motor Company (Ford) is recalling certain 2016-2018 Ford Focus and 2018-2022 Ford EcoSport vehicles. The oil pump drive belt or drive belt tensioner may fail, resulting in a loss of engine oil pressure.
- Risk
- A loss of oil pressure can result in an engine stall and a loss of power braking assist, increasing the risk of a crash.
- Remedy
- Dealers will replace the oil pump tensioner assembly and oil pump drive belt, free of charge. If engine failure occurs due to a damaged oil pump belt and/or oil pump belt tensioner, Ford has authorized dealers to replace the engine assembly as an interim repair before the availability of remedy parts for the final repair. This repair will be free of charge (parts and labor). Owner notification letters were mailed August 11, 2025. Owners may contact Ford customer service at 1‑866‑436‑7332. Ford's number for this recall is 23S64.
Recall number 23V905000 · Recall details
Power train: manual transmission
- What is wrong
- Ford Motor Company (Ford) is recalling certain 2016-2018 Ford Focus vehicles equipped with a 1.0L Fox GTDI engine and a 6-speed manual transmission. The clutch may fracture, resulting in damage to the transmission assembly and possibly a transmission fluid leak.
- Risk
- A transmission fluid leak in the presence of an ignition source such as hot engine or exhaust components can increase the risk of a fire.
- Remedy
- Ford will notify owners, and dealers will update vehicles with software that detects and prevents prolonged clutch slip, and will replace the clutch, as necessary, free of charge. The recall began January 17, 2019. Owners may contact Ford at 1‑866‑436‑7332. Ford's number for this recall is 18S07. Note: This recall is an expansion of Recall 18V‑169.
Recall number 18V845000 · Recall details
Fuel system, gasoline: storage: evaporative emissions: canister
- What is wrong
- Ford Motor Company (Ford) is recalling certain 2012-2018 Ford Focus vehicles with a 2.0L GDI or 2.0L GTDI engine. The Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in fuel vapor management system.
- Risk
- The excessive vaccuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
- Remedy
- Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began August 19, 2019. Owners may contact Ford Customer service at 1‑866‑436‑7332. Ford's number for this recall is 18S32. Note: Until the vehicle is serviced for this concern, owners are advised to keep the fuel tank at least halfway full.
Recall number 18V735000 · Recall details
Power train: manual transmission
- What is wrong
- Ford Motor Company (Ford) is recalling certain 2013-2014 Ford Fusion vehicles equipped with a 1.6L GTDI engine and 6-speed manual transmission and 2015-2016 Ford Focus vehicles equipped with a 1.0L GTDI engine and 6-speed manual transmission. Also included are four 2017 Ford Focus vehicles that had clutch replacements with potentially affected parts. The clutch may fracture, resulting in damage to the transmission assembly and possibly a transmission fluid leak.
- Risk
- A transmission fluid leak in the presence of an ignition source such as hot engine or exhaust components can increase the risk of a fire.
- Remedy
- Ford will notify owners, and dealers will update the Focus vehicles with software that detects and prevents prolonged clutch slip, and will replace the clutch, as necessary, free of charge. Owners of Fusion vehicles will have their clutch assembly replaced free of charge. The recall began August 3, 2018. Owners may contact Ford customer service at 1‑866‑436‑7332. Ford's number for this recall is 18S07.
Recall number 18V169000 · Recall details
Structure: body
- What is wrong
- Ford Motor Company (Ford) is recalling certain 2016 Focus and C-Max vehicles. The floor pan may have improperly welded left-hand apron joints.
- Risk
- Improperly welded apron joints may reduce the front-end structural integrity of the vehicle, increasing the risk of injury in the event of a crash.
- Remedy
- Ford will notify owners, and dealers will inspect the apron joints, repairing the vehicle, as necessary, free of charge. The recall began March 8, 2017. Owners may contact Ford customer service at 1‑866‑436‑7332. Ford's number for this recall is 17S03.
Recall number 17V052000 · Recall details
Latches/locks/linkages: hatchback/liftgate: lock
- What is wrong
- Ford Motor Company (Ford) is recalling certain model year 2013-2017 Ford Focus hatchback vehicles manufactured February 14, 2012, to August 26, 2016 and equipped with a manual transmission. The hatchback of the affected vehicles may be unlatched with a single press of the interior latch release button. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 206, "Door Locks and Door Retention Components."
- Risk
- With only a single press needed, the driver may accidently unlatch the hatchback, increasing the risk of injury to any unsecured passengers in the back.
- Remedy
- Ford will notify owners, and dealers will reprogram the Body Control Module with updated software, free of charge. The recall began February 10, 2017. Owners may contact Ford customer service at 1‑866‑436‑7332. Ford's number for this recall is 16C13.
Recall number 16V698000 · Recall details
See all 10 recalls for the 2016 Ford Focus
Defect investigations
Timing Belt Failure
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODIâs analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehiclesâ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on the federal safety agencyâs analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. ODI is opening this Engineering Analysis to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identiï¬cation Number document, go to
EA26004
Timing Belt Failure
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODIâs analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehiclesâ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on the federal safety agencyâs analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. Therefore, this Preliminary Evaluation is being upgraded to an Engineering Analysis (EA26004). During this Engineering Analysis, the agency plans to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identiï¬cation Number document, go to
PE25020
Oil Pump Failure
On September 20, 2023, the Office of Defects Investigation (ODI) opened PE23-015 to investigate instances of engine failure due to loss of oil pressure in model year (MY) 2018-2021 Ford EcoSport vehicles. Some consumers reported a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle was in motion. The investigation revealed that the engine oil pump drive belt tensioner arm may fracture, separate from the tensioner backing plate, and/or the oil pump drive belt may degrade and lose teeth, resulting in a loss of engine oil pressure. A loss of engine oil pressure can result in engine seizure, which can result in a loss of motive power and a loss of mechanical vacuum pump required to provide power braking assist, increase the risk of a crash. On December 22, 2023, Ford filed recall 23V‑905 for certain MY 2016-2018 Ford Focus and 2018-2022 Ford EcoSport vehicles. The recall remedy provides the replacement of the oil pump drive belt tensioner assembly and oil pump drive belt with redesigned parts to improve robustness. In view of the recall action being taken by Ford, ODI is closing this Preliminary Evaluation. The agency reserves the right to take additional action if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to
PE23015
Loss of Motive Power
On September 15, 2023, the Office of Defect Investigation (ODI) opened this Recall Query (RQ) after receiving 98 consumer complaints alleging loss of motive power in model year (MY) 2012-2018 Ford Focus vehicles. The RQ focused on the effectiveness of the remedies of Recall 18V‑735 and 19V‑515. In October 2018, Ford issued Recall 18V‑735, which updated Powertrain Control Module (PCM) software in MY 2012-2018 Ford Focus vehicles equipped with 2.0L GDI engines built prior to April 13, 2017, and those with 2.0L GTDI engines built prior to February 2, 2018. The recall addressed vehicles experiencing a malfunctioning Canister Purge Valve (CPV) that can stick open and PCM software that does not adequately detect a stuck-open CPV condition. A CPV that is stuck open can cause excessive vacuum in the fuel vapor management system, potentially deforming the fuel tank, collapsing on itself. This deformation of the fuel tank can cause a Malfunction Indicator Light (MIL) to illuminate, an inaccurate or erratic fuel gauge indication, drivability issues, and/or loss of motive power. In July 2019, Ford issued Recall 19V‑515, which addressed certain MY 2012 and MY 2017 Ford Focus vehicles equipped with 2.0L GDI and MY 2013-2014 Ford Focus vehicles equipped with 2.0L GTDI engines whose PCM software had been reprogrammed as a part of recall 18V‑735. The updated software calibrations for these subject vehicles were not properly installed by Ford at the time of production. Approximately one year after this RQ was opened, on September 25, 2024, Ford initiated a customer satisfaction program (24N07) for MY 2012-2018 Ford Focus vehicles equipped with the 2.0L GDI and GTDI engines toâas ODI learned during this investigationâaddress a different issue with the CPV from the primary focus of the safety recalls (18V‑735 and 19V‑515).  Ford stated the CPV may not operate as intended in these vehicles. A failed CPV on its own merit, may cause drivability concerns such as engine hesitation, running rough, or stalling at low speed, which will be accompanied by an illuminated MIL. This program provides a one-time replacement of the CPV for vehicles with 15 years of service or less (with no mileage restriction). This coverage will automatically transfer to subsequent owners. It is to be noted that the customer satisfaction program being taken by Ford to address this RQ investigation results in a much different and significantly less severe problem than the safety action taken to remedy 18V‑735 and 19V‑515. ODI found no further issues with the combined scope and severity related to 18V‑735 and 19V‑515 therefore, ODI is closing this Recall Query. The agency reserves the right to take additional action if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to
RQ23006
Technical service bulletins for the 2016 Ford Focus 200
Bulletins tell dealers how to fix known problems. A warranty extension means the manufacturer pays for that repair for longer.
- Customer Satisfaction Program 26L02 Certain 2014-2021 Model Year Various Vehicles 1.0L Fox Classic Engine...
- Certain 2021-2024 Model Year Bronco, 2021-2024 Model Year Bronco Sport, 2020-2022 Model Year Corsair and...
- Harvest Program 25H05 – Supplement #1 Certain 2011-2021 Model Year Vehicles Software Verification Harvest...
- Advance Notice – Customer Satisfaction Program 25N17 Certain 2015-2025 Model Year Multiple Vehicle Lines...
- Certain 2015
- Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless...
- Certain 2015
- This article supersedes TSB 24-2165 to update the TSB Service Procedure
- This is a proactive investigation program by Ford Motor Company to inspect a limited number of affected...
- Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes...
2016 Ford Focus fuel economy
Official EPA estimates in miles per gallon (MPGe for electric). Ranges cover trims that share the same engine.
| Engine | Drive | City | Highway | Combined |
|---|---|---|---|---|
| 1.0L 3‑cyl | FWD | 28-30 | 39-41 | 32-34 |
| 2.0L 4‑cyl | FWD | 22-27 | 30-39 | 25-31 |
| 2.3L 4‑cyl | AWD | 19 | 25 | 22 |
What 2016 Ford Focus owners say
Most recent owner complaints, unedited.
The vehicle was brought to a certified Ford dealership for an active safety recall and manufacturer extended warranty repair. Due to a malfunction related to the recall issue, the fuel lines were completely ripped off the fuel tank. This component failure is currently available for inspection on the dealership's lot. This failure created an immediate, severe safety risk. Severed fuel lines present an active fuel leak, toxic vapor release, and an extreme fire/explosion hazard in a public dealership parking lot. The physical damage was personally inspected and photographed by me on the dealer's lot. However, the dealership service center is actively refusing to execute the safety recall remedy or fix the severed fuel lines unless I pay out-of-pocket for an unrelated, standard maintenance battery replacement. Furthermore, the dealership provided a multi-point inspection report falsely marking the vehicle status as "all green" despite the severed fuel lines, and they have intentionally withheld the true condition of the vehicle and the required repair orders from the manufacturer's corporate tracking database.
The vehicle is subject to the federal safety agency Safety Recall Campaign 18V‑735 (Ford Recall 18S32) regarding a defective Canister Purge Valve (CPV) that causes fuel vapor saturation, excessive fuel tank vacuum, fuel tank deformation, and engine stalling.The vehicle presented with an active check engine light for diagnostic trouble code P0420 (Catalyst System Efficiency Below Threshold). Ford technical service instructions under Recall 18S32 explicitly link code P0420 to a stuck-open CPV dumping unmetered fuel vapors into the exhaust stream. The franchised dealership initially performed only a software calibration without replacing the mechanical valve.Upon return, the dealership confirmed the defect and replaced the CPV under recall warranty at no charge on Repair Order # 872120. However, dealership service management refused to inspect the catalytic converter for secondary fuel-wash damage unless an unauthorized $220 customer diagnostic fee was paid. The technician cleared the diagnostic trouble codes in the stall without executing the required OBD-II drive cycle. Repair Order # 872120, Line C explicitly documents: "VEHICLE RELEASED FOLLOWING COMPLETION OF RECALL 18S32 WHERE CPV WAS REPLACED. P0420 STATUS PENDING DRIVE CYCLE COMPLETION". Following completion of the required drive cycles, code P0420 returned immediately. Secondary catalytic converter degradation is documented damage resulting directly from the recalled component. Dealership service management has refused to return calls, disconnected phone contact, and ignored written inquiries to avoid submitting the required manufacturer Prior Approval warranty claim for secondary recall remedy. The vehicle and service records are available for inspection upon request.
The vehicle experienced a catastrophic failure of the canister purge valve (CPV), causing an excessive vacuum that violently deformed and collapsed the plastic fuel tank. The deformation was so severe that it breached the fuel system, causing raw gasoline to pour directly out of the filler area and onto the ground when fueling was attempted, presenting an immediate fire hazard. Furthermore, the structural collapse of the fuel tank pinched and shorted out the fuel pump electrical wiring harness. This short circuit caused a massive electrical spike that blew the high-amperage master mega-fuses located on the front of the battery box, causing a total loss of electrical power to the entire vehicle. The manufacturer's initial safety recall remedy (Recall 18S32) failed to prevent this dangerous recurrence, and the vehicle is currently at a dealership being evaluated under Customer Satisfaction Program 24N07.
The DPS6 transmission started out shuddering in low gears even after clutch replacement early on. This made pulling out into traffic slower than it should be. Received “transmission overheating” message “pull over for 5 minutes” in heavy traffic. Prior to the message car would shudder and lose power. This happened suddenly going at highway speeds on the interstate. Replaced clutch actuators and TCM only to have the clutch adaptive learn procedure fail and after inspection by the dealer was told needs new transmission. These problems have been present at very low mileage and Ford now wants to charge a ridiculous amount to replace transmission that should have been fixed long ago. Several times the car stalled in traffic almost causing me to get in accidents.
The contact owns a 2016 Ford Focus. The contact stated that the vehicle stalled while in active traffic. There was no warning light illuminated. Prior to visiting the dealer, the vehicle was taken to two independent mechanics and the vehicle was inspected. The contact was informed that the fuel tank had collapsed. The vehicle was subsequently taken to an authorized dealer for the repair. The dealer diagnosed the vehicle with a failed canister purge valve, but the fuel tank was not damaged. The dealer replaced the canister purge valve and EVAP parts. However, shortly after the repair, the vehicle stalled while driving in traffic. The vehicle was taken to another Ford dealer; however, the dealer experienced the same issue. The manufacturer was notified of the failure and referred the contact back to the dealer for assistance. The contact referenced the federal safety agency Campaign Number: 18V735000 (Fuel System, Gasoline); but the recall repair was already performed on the vehicle. The failure was not repaired. The vehicle had lost motive power and would not restart and had to be towed. The failure mileage was unknown.
I was driving 75mph down I-10 at 11:30pm and my focus sunddenly died, I had to push the car to the shoulder. Information flashed not in park and started ghostly trying to start on its own, I believe the TCM failed. I had to have it towed.
The contact owns a 2016 Ford Focus. The contact stated that while driving at an undisclosed speed, the vehicle unexpectedly stopped accelerating. The contact safely pulled into a parking lot and turned off the vehicle. There was no warning light illuminated. The vehicle was inoperable and was waiting to be towed. The contact associated the failure with the federal safety agency Campaign Number: 23V905000 (Engine and Engine Cooling). The dealer was previously contacted about the recall but was informed that there was no part available for the recall repair. The dealer was not contacted after the failure. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was unknown.
My duel clutch transmission started acting up took it to a mechanic they said it needed the TCM and Actuators and possibly transmission replaced that they should be recalled tried taking it to Thirnhill Ford because I received a letter for this to be changed and they refused without me paying up front this has been going on with my car for over 2 years its setting in a driveway being paid on and cant even be drove
The car would not accelerate when pressing accelerator, they said the clutch assembly malfunctioned, confirmed by documentation. Myself and others had our safety at risk because the car could not be controlled properly while on the road. The car was taken to the dealer and they confirmed the problem. The dealer's service center gave inspection, and confirmed the problem. The warning message did not appear until after the problem put myself and others' safety at risk.
Compare the 2016 Ford Focus
Focus vs Honda CivicFocus vs Toyota CorollaFocus vs Volkswagen JettaFocus vs Hyundai ElantraFocus vs Nissan SentraFocus vs Chevrolet CruzeFocus vs Mazda MAZDA3Focus vs Subaru Impreza
Other model years
19992000200120022003200420052006200720082009201020112012201320142015201620172018
Questions about the 2016 Ford Focus
Is the 2016 Ford Focus reliable?
Owners have filed 1,185 complaints about the 2016 Ford Focus, 1.3 times a typical Focus model year.
What is the 2016 Ford Focus year score?
The 2016 Ford Focus scores 59 out of 100 (below average). The score compares it with the other model years of the Ford Focus: 75 is a typical year, 50 means twice the usual complaints, and serious complaints and recalls lower it.
What is the most common problem with the 2016 Ford Focus?
Transmission and drivetrain, with 674 complaints, typically around 65,000 miles. Next is engine (281).
How many recalls does the 2016 Ford Focus have?
10 recalls, covering fuel system, gasoline, power train and equipment.
What gas mileage does the 2016 Ford Focus get?
Official estimates for the 2016 Ford Focus range from 22 to 34 mpg combined. The most efficient version (1.0L 3-cyl, FWD) gets 28-30 city and 39-41 highway.
VIN decoder
See the problems and recalls for an exact car
Buying a used 2016 Ford Focus?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its history