2003 Ford Windstar problems

What is wrong

Ford Motor Company (Ford) is recalling certain model year 1998-2003 Windstar vehicles manufactured September 2, 1997, to July 3, 2003. The affected vehicles were previously remedied to safeguard against the rear axle cracking from corrosion, however, the remedy brackets may have been misinstalled. The incorrect bracket installations may limit the effectiveness of the service repair for the federal safety agency recalls 10V‑385, 12V‑193, and 12V‑195.

Risk

If the brackets were not installed properly, the rear axle may fracture, affecting the vehicle handling and increasing the risk of a crash.

Remedy

Ford will notify owners, and dealers will inspect the brackets to verify their proper installation. If a bracket is found to have been misinstalled, the rear axle will be replaced. These repairs will be performed free of charge. The began on October 21, 2015. Owners may contact Ford customer service at 1‑866‑436‑7332. Ford's number for this recall is 15S27.

Recall number 15V608000 · Recall details

What is wrong

Ford is recalling certain model year 1998-2003 windstar vehicles manufactured from september 1, 1997, through july 3, 2003, and currently registered or originally sold in virginia. Over time, corrosion can weaken the rear axle making it susceptible to torsional stress. Corrosion and stress can lead to cracks which, if undetected, can increase and result in a complete fracture of the axle.

Risk

A fractured axle can affect vehicle handling and increase the risk of a crash.

Remedy

Ford will notify owners, and dealers will inspect and install rear axle reinforcement brackets, or replace the axles, as necessary. This service will be performed free of charge. The recall began on june 19, 2012. Owners may contact ford at 1‑866‑436‑7332.

Recall number 12V193000 · Recall details

What is wrong

Ford is recalling certain model year 1999-2003 windstar vehicles originally sold in or currently registered in the state of virginia. Corrosion-related fractures of the front lower control arm rear attaching brackets and body mount attachments may occur.

Risk

A separation of a front lower control arm rear attaching bracket may result in a lower control arm separation. A separation of both front subframe rear body mounts may result in separation of the steering intermediate shaft. Either condition could result in significant loss of steering control, increasing the risk of a crash.

Remedy

Dealers will inspect both front lower control arm rear attaching brackets and both body mount attachments at the rear of the front subframe and make the necessary repairs free of charge. The recall began on june 18, 2012. Owners may contact ford at 1‑866‑436‑7332.

Recall number 12V194000 · Recall details

What is wrong

Ford is recalling certain model year 1998-2003 windstar vehicles manufactured from september 1, 1997, through july 3, 2003, registered in puerto rico. Due to increased stresses caused by high cycles of torsional loading, specific to this market, the rear axle can crack.

Risk

A fractured axle may result in a loss of vehicle control, increasing the risk of a crash.

Remedy

Ford will notify owners, and dealers will inspect and install a reinforcement bracket on the rear axle or replace the axles, as necessary. This service will be provided free of charge. The recall began on june 1, 2012. Owners may contact the ford motor company customer relationship center at 1‑866‑436‑7332.

Recall number 12V195000 · Recall details

What is wrong

Ford is recalling certain model year 1999-2003 windstar vehicles originally sold in or currently registered in the states of connecticut, delaware, the district of columbia, illinois, indiana, iowa, kentucky, maine, maryland, massachusetts, michigan, minnesota, missouri, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, utah, vermont, west virginia, and wisconsin. A separation of a front lower control arm rear attaching bracket may result in a lower control arm separation. A separation of both front subframe rear body mounts may result in separation of the steering intermediate shaft.

Risk

This could result in reduced steering control increasing the risk of a crash.

Remedy

Dealers will inspect both front lower control arm rear attaching brackets, and both body mount attachments at the rear of the front subframe, and make the necessary repairs free of charge. If repairs cannot be made to a vehicle, ford will offer to repurchase the vehicle. The safety recall is expected to begin on or before february 21, 2011. Owners may contact ford at 1‑866‑436‑7332.

Recall number 11V030000 · Recall details

What is wrong

Ford is recalling certain model year 1998-2003 windstar vehicles manufactured from september 1, 1997 through february 28, 2003 and currently registered or originally sold in connecticut, delaware, district of columbia, illinois, indiana, iowa, kentucky, maine, maryland, massachusetts, michigan, minnesota, missouri, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont, west virginia, and wisconsin. After many years of vehicle service in these areas, corrosion can weaken the rear axle, making it susceptible to torsional stress. Corrosion and stress can lead to cracks which if undetected can propagate and result in a complete fracture of the axle.

Risk

A fractured axle can affect vehicle handling and increase the risk of a crash.

Remedy

As parts become available, dealers will inspect and if necessary install the rear axle reinforcement brackets free of charge. This service will be performed free of charge. The safety recall began on october 20, 2010. Owners may contact ford at 1‑866‑436‑7332.

Recall number 10V385000 · Recall details

What is wrong

Ford is recalling model years 1995-2003 windstar, 2000-2003 excursion diesel, 1993-1997 and 1999-2003 f-250 sd through f-550 sd diesel, 1992-2003 e-150 through e-550, 1995-2002 explorer, 1997 and 2002 mercury mountaineer, 1995-1997 and 2001-2003 ranger, and 1994 f53 vehicles equipped with the texas instruments speed control deactivation switch (scds). The scds may leak internally and then overheat, smoke, or burn.

Risk

A vehicle fire could occur with or without the engine running.

Remedy

Ford will notify owners that dealers will install a fused wiring harness in line with the scds. On 1999-2003 windstar vehicles with a leaking scds, dealers will also inspect the ABS control module connector and repair as necessary. Repairs will be completed free of charge. The safety recall began on october 27, 2009. Owners may contact ford at 1‑888‑222‑2751.

Recall number 09V399000 · Recall details

What is wrong

Certain minivans fail to comply with the requirements of federal motor vehicle safety standard no. 225, "child restraint anchorage system." during testing, a third row bench floor-to-seat latch released before the strength requirement was met. Identical latches are used in the second row of seats.

Risk

If the latches on th4e second or third row seats of the vehicle release in a crash, the potential for occupant injury is increased.

Remedy

Dealers will replace the seat-to-floor latches on the second and third row of seats. Owner notification began on november 21, 2003. Owners should contact ford at 1‑800‑392‑3673.

Recall number 03V459000 · Recall details

In a January 26, 2011 Defect Information Report, Ford Motor Company (Ford) notified the federal safety agency that it will conduct a safety recall to address corrosion related fractures in the front lower control arm rear attaching brackets and body mount attachments at the rear of the front subframe in approximately 425,288 model year (MY) 1999 through 2003 Ford Windstar vehicles manufactured from April 1998 to July 2003 and either sold or currently registered in the following high corrosion (Salt-Belt) states:Connecticut, Delaware, District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Utah, Vermont, West Virginia and Wisconsin (the federal safety agency Recall No. 11V‑030, Ford Recall No. 11S16).According to Ford, separation of a front lower control arm rear attaching bracket may result in a lower control arm separation and separations of both front subframe rear body mounts may result in separation of the steering intermediate shaft.Either condition could result in diminished vehicle directional control, increasing the risk of a crash.Dealers will inspect the lower control arm rear attachment flanges and the rear body mount sections of the subframe on the right (passenger) and left (driver) sides of the vehicle.Owners of vehicles that pass the inspection will be notified when to return for installation of reinforcement brackets to extend the durability of the front subframe assembly in affected areas in the presence of corrosion.Owners of vehicles that do not pass inspection, but can be repaired, will be offered transportation until parts become available.Repurchase offers will be extended to owners of vehicles that cannot be repaired with the reinforcement brackets.This investigation is closed.

EA10007

On November 5, 2010, the federal safety agency received a Defect Petition from the owner of a MY 2003 Ford Windstar vehicle registered in the state of New York requesting that the scope of Recall 10V‑385 be expanded to include additional MY 2003 vehicles experiencing the defect condition.The petitioner initially filed a complaint (VOQ 10345125) with ODI on July 25, 2010, two days after the axle failure.The complaint was subsequently amended and the petition filed after the consumer was denied compensation and repair under the recall.ODI has identified a total of five complaints from owners of MY 2003 Ford Windstar vehicles in Salt Belt states that were built after February 28, 2003, Ford's original cutoff date for 10V‑385.On November 30, 2010, Ford submitted a letter supplementing recall 10V‑385 (Ford 10S13) to add certain vehicles to the program.Ford's analysis of parts and information from the field showed: 1) that the revised heat treated axle introduced in production on February 28, 2003, may still have the potential for cracks due to corrosion related stress; and 2) that vehicles operated in Utah may be exposed to the same combination of environmental factors that can make them susceptible to cracks from stress related corrosion.Based on this analysis, Ford expanded the scope of 10V‑385 to include MY 2003 vehicles built after February 28, 2003 and sold or currently registered in Salt Belt states and MY 1998 through 2003 vehicles sold or currently registered in Utah.Ford estimated that approximately 29,900 vehicles in the expanded scope may currently remain in service.Based on the above amended defect report submission, the petition has become moot and is therefore denied.

DP10005

The Office of Defects Investigation (ODI) has identified 346 complaints to ODI and Ford alleging fracture, cracking and or excessive corrosion of the front subframes in model year (MY) 1999 through 2003 Ford Windstar vehicles.Approximately 97 percent of these complaints (334) involve vehicles that have been operated in Salt Belt states, which make up approximately 60 percent of the subject vehicle sales in the United States.The front subframe, sometimes referred to as the engine cradle, is a structural component of the Windstar vehicles that carries the engine, transaxle, steering rack and certain front suspension components (e.g., lower control arm).For complaints with sufficient information to identify the location of the failure, most describe problems with the rear mounting bracket for the front passenger-side lower control arm with some related to the rear body mount attachment located in the same general area of the subframe (right-rear section near the front passenger wheel).The remainder of the reports allege fracture of the front subframe at other or, most often, unspecified locations.Almost all of the complaints that specified the side of the vehicle indicated that the problem occurred on the right/passenger side (106), with only a few indicating the left/driver side (2) or both sides (3) were affected.Ford and several complainants attributed the right-side failures to the routing of the air-conditioning lines above the front subframe on that side of the vehicle, further noting that condensation has been observed dripping onto the front subframe in the area of the affected components (the A/C drain tube is also located on the right side, near the front subframe).ODI has identified 93 complaints related to lower control arm attachments, including 80 that appear to involve complete separations.All but one of these involved vehicles from Salt Belt states.All three crash incidents appear to be related to lower control arm separations, including one road departure into a road-side sign resulting in a totalled vehicle and a lane departure into another vehicle.Almost half of the ODI complaints related to control arm separation occurred at speeds greater than 20 mph and about a quarter occurred at highway speeds.Three-quarters of these complaints allege experiencing difficulty controlling the vehicle and about 40 percent appear to have resulted in departures from the intended lane of travel.Testing by both Ford and the federal safety agency have demonstrated that lower control arm separation from the rear attachment bracket results in significant toe out of the affected wheel, which affects the driver's ability to control vehicle direction.According to Ford, moderate braking improved vehicle controllability by reducing the amount of toe out, possibly explaining incidents that did not allege a loss of control.ODI's analysis of complaints related to the rear body mount identified 41 complaints (ODI only).These complaints generally report experiencing progressively worsening noise concerns when turning, accelerating or braking.Although, some of the complaints that appeared to involve a complete separation of the body mount alleged difficulty steering, the effects on vehicle control from this failure mode do not appear to be as great as those resulting from control arm separation.However, ODI is seeking more information regarding two complaints which alleged that body mount failure resulted in disconnection of the steering wheel from the steering rack (one occurred during vehicle service).This investigation has been upgraded to an Engineering Analysis (EA10-007) for subject vehicles sold or currently re

PE10026

In a letter dated August 26, 2010, Ford Motor Company (Ford) submitted a Defect Information Report notifying the federal safety agency that it will conduct a safety recall (the federal safety agency Recall No. 10V‑385) to address a rear axle defect in model year (MY) 1998 through 2003 Ford Windstar vehicles built at the Oakville assembly plant from September 1, 1997 through February 28, 2003 and either sold or currently registered in high corrosion (Salt-Belt) states where the use of salt and other corrosive chemicals may be used to treat snow/ice covered roads.The following states are included in Ford's recall:Connecticut, Delaware, District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia and Wisconsin. The subject vehicles utilize a Stamped/Formed axle assembly manufactured by Benteler automotive Corporation of Galesburg, MI.According to Ford, after many years of vehicle service in the Salt-Belt states, corrosion can weaken the rear axle, making it susceptible to torsional stress.There is a risk that the combined effects of corrosion and stress can lead to cracks which, if undetected, can propagate and result in a complete fracture of the axle.A completely fractured axle can affect vehicle handling and increase the risk of a crash.To correct the safety defect, Ford will initially inspect all of the subject vehicles brought into Ford/Lincoln-Mercury dealerships for possible cracked axles.Owners of vehicles without cracked axles will be notified when to return for the installation of reinforcement brackets to extend the axle durability in the presence of corrosion.Owners who have vehicles with cracked axles will either be offered a repair or alternative transportation until parts become available. On May 13, 2010, the Office of Defects Investigation (ODI) opened PE10-016 to investigate complaints of rear axle cracking in MY 1999 through 2003 Ford Windstar minivans.Combining ODI and Ford complaint data, ODI is aware of a total 891 complaints alleging rear axle cracking in the subject vehicles.Over a third of the complaints (334) allege that the cracking progressed to a complete fracture of the rear axle, including 8 allegations of crashes resulting in 3 injuries. Approximately 57 percent of the subject vehicles (524,661) were sold in Salt-Belt states covered by Ford's recall and Ford estimates that approximately 463,000 of these remain in service.Ninety-six percent of the complaints (858) and all of the complaints alleging complete fracture were from the recall region.The action taken by Ford is sufficient to resolve the issues raised by this investigation.Accordingly, this investigation is closed.

PE10016

Ea08-021 is closed with ford's actions in recall 09v‑399 recalling approximately 4.5 million vehicles equipped with texas instruments speed control deactivation switches (scds).with this recall ford has now recalled all of the approximate 16 million ford model vehicles that were manufactured from my 1992 through 2003 with a texas instruments scds.the federal safety agency will continue to monitor the recalled vehicles to ensure remedies installed by ford tomitigate the potential for scds related fires are effective.the agency reserves the right to take further action if warranted by the circumstances.see attached closing report for further details.

EA08021

Odi has received 134 consumer complaints, 285 manufacturer complaints, and 137 manufacturer warranty claims alleging incidents of engine compartment fire in model year (my) 1995 thru 2003 ford windstar vehicles.two of the odi complaints allege the fires caused structural damage to the complainant's home.of the 134 odi complaints, 36 allege the fire occurred while the vehicle was parked, 72 allege the fire occurred while the vehicle was running and 26 of the complaints do not specify if the vehicle was running or not.further review of the odi complaints shows that 72 allege that the speed control deactivation switch (scds) caused the fire and 10 allege that the scds leaked brake fluid on to the ABS module resulting in the fire.there were 52 that did not identify a cause or that identified miscellaneous other causes.odi has also received 89 complaints ( not counted in this resume) alleging that the scds developed a brake fluid leak.thirteen of these complaints say that the leak at the scds resulted in braked fluid reaching the ABS module.this pe has been upgraded to an engineering analysis (ea) to further evaluate the cause of the fires and assess the scope, frequency, and safety consequences of the alleged defect.

PE08035