2017 Ram 2500 problems

What is wrong

Chrysler (FCA US, LLC) is recalling certain 2016-2019 Ram 3500, Ram 1500, 2016-2020 Ram 2500, and 2016 Ram 3500 Cab Chassis vehicles. The right and left side curtain air bag inflators may rupture due to a manufacturing defect.

Risk

An inflator rupture may result in sharp metal fragments striking occupants, resulting in injury.

Remedy

Dealers will replace one or both side curtain air bags, as necessary, free of charge. Owner notification letters were mailed February 13, 2025. Owners may contact FCA customer service at 1‑800‑853‑1403. FCA's numbers for this recall are 05C, 09C, and 10C.

Recall number 25V010000 · Recall details

What is wrong

Chrysler (FCA US, LLC) is recalling certain 2017-2018 Ram 2500 Pickup, Ram 3500 Pickup, 3500 Cab Chassis, 4500 and 5500 Cab Chassis vehicles. The hydraulic control unit (HCU) may fail, which can cause the anti-lock brake (ABS), electronic stability control (ESC), and traction control systems to fail.

Risk

A loss of anti-lock brakes, electronic stability control, or traction control can increase the risk of a crash.

Remedy

Dealers will replace the brake HCU, or replace the HCU motor, free of charge. Owner notification letters were mailed beginning January 9, 2025. Owners may contact FCA customer service at 1‑800‑853‑1403. FCA's number for this recall is C4B.

Recall number 24V896000 · Recall details

What is wrong

Chrysler (FCA US LLC) is recalling certain 2015-2017 Ram 1500, 2500 and 3500 pickup trucks equipped with an 8 foot bed and a power locking tailgate. Chrysler is also recalling all 2013-2014 and 2018 Ram 1500, 2500 and 3500 pickup trucks built before April 1, 2018 with a 6 or 8 foot bed and a power locking tailgate. On August 29, 2019 Chrysler expanded the recall to include an additional 693,128 model year 2013-2014 Ram 1500, 2500 and 3500 pickup trucks. The tailgate actuator limiter tab may fracture and cause the tailgate to unlatch and open while driving.

Risk

If the tailgate opens while the vehicle is being driven, cargo may fall out the vehicle and create a road hazard, increasing the risk of crash.

Remedy

Chrysler will notify owners, and dealers will repair the tailgate latch, free of charge. The recall began May 23, 2019. Chrysler is expected to notify owners of the expanded population on October 18, 2019. Owners may contact FCA US customer service at 1‑800‑853‑1403. FCA US's number for this recall is V44. Note: 2015-2017 MY Ram 1500 pickup trucks with truck beds other than 8 foot, are currently covered under the federal safety agency recall 18V‑486 for this issue.

Recall number 19V347000 · Recall details

What is wrong

Chrysler (FCA US LLC) is recalling certain 2013-2018 Ram 3500 and 2014-2018 Ram 3500 Chassis Cab and Ram 2500 vehicles. The outboard steering linkage jam nut may loosen, allowing one end of the drag link to separate.

Risk

A drag link separation can cause a loss of steering control, increasing the risk of crash.

Remedy

Chrysler will notify owners, and dealers will check the steering linkage jam nut tightness, replacing the drag link assembly or welding the nut to the adjuster sleeve, free of charge. The recall began March 22, 2019. Owners may contact Chrysler customer service at 1‑800‑853‑1403. Chrysler's number for this recall is V06.

Recall number 19V021000 · Recall details

What is wrong

Chrysler (FCA US LLC) is recalling certain 2015-2017 RAM 1500, 2500, and 3500 pickup trucks equipped with a power locking tailgate and either a 5 foot, 7 inch or 6 foot, 4 inch bed. The tailgate actuator limiter tab may fracture and cause the tailgate to unlatch and open while driving.

Risk

If the tailgate latch releases and the tailgate opens while driving, cargo may fall out, creating a road hazard and increasing the risk of a crash.

Remedy

Chrysler will notify owners, and dealers will repair the vehicle, free of charge. The recall began September 17, 2018. Owners may contact Chrysler customer service at 1‑800‑853‑1403. Chrysler's number for this recall is U74.

Recall number 18V486000 · Recall details

What is wrong

Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.

Risk

If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.

Remedy

Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1‑800‑853‑1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.

Recall number 18V332000 · Recall details

What is wrong

Chrysler (FCA US LLC) is recalling certain 2017-2018 RAM 1500, 2500, 3500, 3500 Cab Chassis, 4500 Cab Chassis, and 5500 Cab Chassis vehicles, all equipped with a column shifter. Pushing the brake pedal for prolonged periods when the vehicle is running and in PARK may cause the Brake Transmission Shift Interlock (BTSI) pin to stick in the open position. With the pin in the open position, the transmission can be shifted out of PARK into any gear without pushing the brake pedal or having the key in the ignition.

Risk

Being able to shift the transmission without pushing the brake pedal and/or without a key in the ignition can increase the risk of an unintended vehicle rollaway that may result in personal injury or a crash.

Remedy

Chrysler will notify owners and dealers will update the Body Control Module software. Dealers will also test the BTSI operation, replacing the solenoid as necessary. The recall began February 26, 2018. Owners may contact Chrysler customer service at 1‑800‑853‑1403. Chrysler's number for this recall is U11.

Recall number 18V100000 · Recall details

What is wrong

Chrysler (FCA US LLC) is recalling various Dodge, Chrysler, and RAM vehicles equipped with Kidde Plastic-Handle or Push Button 'Pindicator' Fire Extinguishers. A list of the affected trailer models is available at: These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit:

Risk

If the fire extinguisher does not function properly, it can increase the risk of injury in the event of a fire.

Remedy

Chrysler will notify owners instructing them to contact Kidde for a replacement fire extinguisher, free of charge. The recall began February 14, 2018. Owners may contact Chrysler customer service at 1‑800‑853‑1403 or Kidde customer service service toll-free at 1‑855‑262‑3540, or online at www.kidde.com and click on "Product Safety Recall" for more information. Chrysler's number for this recall is T82.

Recall number 17V824000 · Recall details

What is wrong

Chrysler (FCA US LLC) is recalling certain 2016-2017 Ram 3500 Cab Chassis with a Gross Vehicle Weight Rating (GVWR) of less than 10,000 lbs, 2011-2017 Ram 3500, 4500 and 5500 Cab Chassis vehicles, 2009-2017 Ram 1500 and 2010-2017 Ram 2500 and 3500 pickup trucks, all equipped with a column shifter. Pushing the brake pedal for prolonged periods when the vehicle is running and in PARK may cause the Brake Transmission Shift Interlock (BTSI) pin to stick in the open position. With the pin in the open position, the transmission can be shifted out of PARK into any gear without pushing the brake pedal or having the key in the ignition.

Risk

Being able to shift the transmission without pushing the brake pedal and/or without a key in the ignition can increase the risk of an unintended vehicle rollaway that may result in personal injury or a crash.

Remedy

Chrysler will notify owners, and dealers will update the vehicle software, inspect the BTSI, and, as necessary, replace it, free of charge. The recall began February 26, 2018. Owners may contact Chrysler customer service at 1‑800‑853‑1403. Chrysler's number for this recall is T79.

Recall number 17V821000 · Recall details

What is wrong

Chrysler (FCA US LLC) is recalling certain 2013-2017 RAM 2500, 3500, 3500 Cab Chassis, 4500 Cab Chassis, and 5500 Cab Chassis vehicles, equipped with Cummins 6.7L Turbo Diesel engines that have Concentric-brand water pumps without a vent hole. These water pumps may leak coolant.

Risk

The leaking water pump can increase the risk of an engine compartment fire.

Remedy

Chrysler will notify owners, and dealers will replace the water pumps, free of charge. The recall began February 26, 2018. Owners may contact Chrysler customer service at 1‑800‑853‑1403. Chrysler's number for this recall is T51.

Recall number 17V562000 · Recall details

What is wrong

Streetcar ORV LLC, dba American Expedition Vehicles (AEV) is recalling certain 2013-2017 RAM 2500 and 3500 heavy duty trucks, modified by AEV to be equipped with cast aluminum Katla 8.5" road wheels. The outer surface of the wheel may fracture, resulting in rapid air loss.

Risk

If the wheel fractures, a loss of vehicle control can occur, increasing the risk of a crash.

Remedy

AEV will notify owners, and dealers will replace the wheels with wheels of similar value, free of charge. The recall began on August 30, 2017. Owners may contact AEV customer service at 1‑248‑926‑0256 extension 500.

Recall number 17V499000 · Recall details

The Office of Defects Investigation (ODI) has received 14 Vehicle Owner Questionnaire (VOQ) reports and 6 EWR Death & Injury (D&I) reports describing post recall remedy failures of the brake transmission shift interlock (BTSI) system in certain Model Year (MY) 2013-2018 RAM pickup trucks.The subject vehicle models include 1500, 2500, 3500, 4500, and 5500 trucks equipped with a column mounted shift lever.The failures of the BTSI described in the VOQs occurred on vehicles that had all previously been repaired under recall 17V‑821 or 18V‑100.Both recalls address a potential condition which can cause the BTSI locking pin to become stuck allowing the transmission to be shifted out of Park without depressing the brake pedal and/or without having a key in the ignition.Shifting the transmission out of Park when not having the brake pedal depressed can result in a vehicle rollaway. ODI is opening this Recall Query (RQ) to review the effectiveness of the 17V‑821 and 18V‑100 recall remedies, understand the root cause of additional vehicle rollaway incidents, and identify any other possible root cause that may affect the performance of the BTSI system. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to

RQ25003

The Office of Defects Investigation (ODI) opened this investigation on November 28, 2022, after receiving 134 reports from consumers alleging an intermittent or permanent loss of braking performance in certain 2017-2018 Ram 2500-3500 pickup trucks manufactured by Fiat Chrysler Automobiles (FCA). The alleged failures continued to occur at a steady rate across both models, at all speeds, with limited detectability. Consumers complained that the Anti-lock Braking System (ABS) warning light illuminated on their vehicles. The ABS module works in conjunction with the Hydraulic Control Unit (HCU), an electromechanical device that controls hydraulic pressure to the individual wheel brake assemblies, to manage braking forces during emergency stops. During this investigation, ODI received over 2,500 consumer complaints concerning ABS or HCU warning lights that illuminated on the dashboards of their vehicles. Many consumers described also having trouble with cruise control, traction control, or electronic stability control. Of the complaints received, over 50% mentioned that the ABS or HCU warning light was intermittent in nature. ODI learned that in January 2021, FCA was aware of a problem with the ABS pump motors on the subject vehicles. FCA had been working with the supplier, ZF, on an issue concerning swelling of the brushes inside the motor. According to a briefing given by ZF to FCA on January 15, 2021, the ABS, electronic stability control (ESC), traction control system (TSC) and other functions utilizing the motor would be disabled in the event of a problem with an ABS pump motor. ZF also informed FCA that Slip Control would be inhibited with the driver warning lamp illuminated, base braking would not be affected, and FMVSS stopping distance requirements would still be met. In order to better understand the potential consequences of the brushes swelling and the disablement of the ABS, ESC, TSC and other functions, ODI requested that the federal safety agency's Vehicle Research and Test Center (VRTC) conduct testing on a subject vehicle with a faulty pump motor installed. During the testing, VRTC found that as the brushes started to swell in the motor, the warning lamp could illuminate intermittently, causing confusion to drivers. Although the warning light illuminated intermittently, VRTC discovered that the pump was not working properly regardless of the warning light status. In this condition drivers might think that their vehicle is operating normally when the warning light is off, but instead, the ABS, ESC, TSC and other functions supported by the pump will not work. Following a series of meetings with FCA to demonstrate the findings ofVRTC's testing, FCA conducted an internal review and on November 27, 2024, FCA submitted safety recalls 24V‑896 and 24E-100. In view of the recalls being conducted by FCA, ODI has closed this Preliminary Evaluation. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to

PE22012

On December 17, 2018, the federal safety agency's Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18016 to investigate alleged drag link failures in the steering system on model year (MY) 2015 and 2016 Ram 2500 trucks manufactured by FCA US, LLC (FCA).  The drag link failures were found to be due to a safety defect with the steering linkage where the drag link adjustable connector (used to adjust the steering system), held in position by two opposing jam nuts, can loosen.  The loosening of this part can lead to wear and deterioration of the threads and eventual separation of the drag link, causing loss of steering. During the course of PE18016, it was found that two styles of drag link were used by FCA on the subject vehicles.  The subject vehicles consist of two drivetrain types including four-wheel drive (4WD) and two-wheel drive (2WD). The 4WD and 2WD trucks used drag links of differing design but both incorporated the same threaded connector. In January 2019 FCA issued recall 19V‑021 to address a potential loss of steering control in certain Model Year (MY) 2013-2018 4WD RAM 2500 and 3500 trucks. The trucks using the 2WD style drag link were not included in the scope of recall 19V‑021. ODI upgraded PE18016 to an Engineering Analysis EA19004 on December 12, 2019.  The purpose of EA19004 was to investigate if the root cause of the safety defect addressed by recall 19V‑201 also affected the 2WD trucks and evaluate FCA’s rationale for not including them. ODI also monitored incoming consumer complaints regarding the remedy associated with 19V‑021 and evaluated the suitability and long-term effectiveness of the prescribed repair. In the Defect Information Report submitted for recall 19V‑021, FCA stated that the outboard jam nut could loosen and result in damage to the threading of the steering drag link connector.  This could cause a separation in the drag link resulting in a loss of steering control.  FCA determined that only the 4WD style drag link was affected and did not recall trucks with the 2WD style drag link due to design differences that made it unsusceptible to this failure mode.  The repair remedy called for the steering coupler to be tightened to the proper torque prior to the jam nut being spot welded to the coupler body. If the coupler has already become detached or correct torque cannot be obtained, the drag link is to be replaced with an updated unit that went into production on the MY2019 RAM trucks.This updated unit uses a clamp to secure the coupler in place of the jam nuts used on original style components. In order to determine if the 2WD drag link was susceptible to the same defect found on the 4WD vehicles, ODI requested that our Vehicle Research and Test Center (VRTC) conduct testing on both RAM 2500 4WD and 2WD trucks. This testing was to determine operating conditions that might lead to loosened jam nuts of the recalled 4WD design and recreate these conditions on the 2WD vehicles to discover whether the 2WD design would also experience the loosening defect. Results from VRTC’s dynamic testing indicated that when the jam nuts are significantly under-torqued, they may loosen further from regular vehicle operation on the 4WD vehicles. Further, VRTC testing does not refute FCA’s assertion that the failure mechanism does not exist in the 2WD steering system. At the time of this closing resume, ODI has only received two allegations of drag link separation on 2WDvehicles.Neither could be validated as resulting from loose jam nuts. Since the release of recall 19V‑021 ODI has received consumer complaints regarding the appearance of the spot weld applied to the defective drag link and the inability to have the steering properly aligned after welding of the jam nut.  In September 2023, FCA provided owners with a supplemental Vehicle Alignment Clarification notification that provided information on an updated alignment procedure. Regarding the spot weld remedy used on the 4WD vehicles, ODI is concerned about the remedy in that during an alignment by a non-dealer repair facility, the spot weld might not be replaced after the alignment.  To date there is no complaint trend of post alignment drag link separations, weld failures or other safety related incidents on remedied vehicles. This investigation is being closed with no further action. The closing of this investigation does not constitute a finding by the federal safety agency that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances.

EA19004

On December 17, 2018, the federal safety agency's Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 18-016 to investigate the steering system on model year (MY) 2015 and 2016 Ram 2500 manufactured by FCA US, LLC (FCA). Four complaints were received alleging separation of the drag link, a steering linkage that connects between the right front steering knuckle and the pitman arm on the steering box output shaft. The failures were found to be at a threaded coupler within the drag link used for adjusting the length of the linkage during routine maintenance (alignment) of the steering system.Once separation occurs, turning the steering wheel has no effect, and there is no way for the driver to control or maintain the direction of the vehicle. During the investigation, it was determined that the same threaded coupler was used on two different drag link designs FCA manufactured on MY 2013-2018 Ram 2500 and 3500 pickups. FCA refers to the designs as either 4x2 or 4x4 style. In both designs, the coupler is prevented from turning on the drag link via two jam nuts that are tightened against the coupler. In its response to the federal safety agency's March 15, 2019, Information Request (IR) letter, FCA identified 48 incidents alleging separation of the steering linkage at the coupler resulting in a loss of steering control. Of those, 13 involved a crash, one of which resulted in an injury. All of the separations involved the 4x4 style drag link. Additionally, FCA's IR response refers to over 300 4x4 style equipped vehicles that experienced, or may have experienced loosening of one or more coupler jam nuts. On January 25, 2019, FCA submitted a Defect Information Report (DIR) initiating the federal safety agency Recall No. 19V‑021. In its DIR, FCA stated that the outboard jam nut in certain MY 2013-2018 Ram 2500 and 3500 could loosen potentially resulting in damage to the coupler and/or drag link threading allowing one end of the drag link to separate. The DIR notes that drag link separation results in loss of steering control, which in turn can cause a crash without warning. FCA's DIR did not identify a root cause for the defect, however it posits that an improperly torqued outboard jam nut could loosen, and with long-term vehicle use, cause damage to the outer link bar and/or coupler threads due to relative motion between the two components. The scope of Recall 19V‑021 included vehicles with the 4x4 style drag link only. Also discussed in its IR response, FCA noted that the 4x2 style drag link contains a design difference (the outboard portion of the drag link is straight while the 4x4 style contains a bend) which it suggests may result in differences in the mechanical (bending) loads presented at the coupler and jam nut interface. Moreover, the DIR states that While root cause of the 4x4 style defect has not been established, FCA US believes that bending loads on the drag link is, at least, a causal contributing factor. FCA notes it did not identify any reports alleging 4x2 style separation as well as only three reports of loosening of jam nuts, two of which resulted in loosening that provided obvious warning to the vehicle operator, indicating a different failure mode.the federal safety agency is upgrading this investigation to Engineering Analysis (EA) 19-004 in order to continue to monitor the subject 4x2 style vehicles for evidence of field failures. Additionally, in conjunction with the federal safety agency's Vehicle Research and Test Center, ODI intends to more thoroughly study potential root cause(s) of the 4x4 style defect mechanism, and if identified, will seek to determine if the 4x2 drag link is susceptible to the same mechanism(s). the federal safety agency will also evaluate the long-term suitability of the recall

PE18016