My 2019 Jeep Wrangler JL has developed a severe, recurring electrical malfunction that causes multiple vehicle systems to fail simultaneously, resulting in unexpected loss of propulsion and the vehicle automatically shifting into Park without driver input. The issue initially began with an intermittent “Service Shifter” warning, particularly when driving over bumps or braking. At first, the vehicle continued operating normally. After several weeks, the problem progressively worsened. Now, numerous dashboard warning lights illuminate simultaneously, including the battery, oil pressure, and brake indicators. The speedometer fluctuates erratically, and warnings such as “Service Electronic Stability Control” appear. The vehicle begins jerking, slowing down unexpectedly, and eventually loses propulsion. It may initially continue moving, but the malfunction progresses until the vehicle shifts into Park without my input, preventing further operation. During one extremely dangerous incident, the vehicle malfunctioned and became disabled in the fast lane of [XXX], leaving me stranded in active highway traffic. I discovered that physically pressing down on electrical components connected to the dashboard fuse box sometimes temporarily restores normal operation after restarting the vehicle. However, the malfunction continues to recur and has become increasingly frequent. My VIN shows no outstanding safety recalls, but I am concerned about a potential electrical, wiring, power distribution, or electronic communication defect. The exact cause has not been diagnosed. I have video evidence of the dashboard malfunction and warning messages. I am requesting an investigation because this unpredictable failure creates a serious collision risk, particularly at highway speeds. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The worst 2019 Jeep Wrangler problems
Ranked by number of owner complaints. Mileage and cost come from what owners wrote.
Problems by type
Tap a problem to see which part fails, at what mileage and in which other years.
- Steering448
- Electrical153
- Suspension134
- Transmission81
- Engine49
- Brakes32
- Visibility30
- Wheels28
- Body22
- Acceleration19
- Driver assistance18
- Fuel system10
- Seats7
- Seat belts6
- Airbags4
- Lights2
- Tires1
Specific symptoms reported on the 2019 Jeep Wrangler
Pulling 111Power steering loss 44Check engine light 36ABS 34Loss of power 30Wipers 24Warning lights 23Fuel gauge 16Jerking 15Stalling 14Steering lock-up 14Won't shift 14Fire or smoke 12Won't start 10Engine failure 9Overheating 9Ball joint 8Screen failure 8Backup camera 6Start-stop 6Shudder 5Slipping 5
Recalls 9
Back over prevention: sensing system: camera
- What is wrong
- Chrysler (FCA US, LLC) is recalling certain 2018-2024 Jeep Wrangler vehicles. The wiring harness for the rearview camera and the center brake light may short circuit, which can disable the rearview camera image and center brake light. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 111, "Rear Visibility" and 108, "Lamps, Reflective Devices, and Associated Equipment."
- Risk
- A rearview camera image that does not display decreases the driver's visibility, increasing the risk of a crash. Additionally, a center brake light that fails to illuminate can fail to indicate to other drivers that the vehicle is slowing down, increasing the risk of a crash.
- Remedy
- Dealers replaced the harness for the center brake light and rearview camera and/or the spare tire carrier/harness assembly, as necessary, free of charge. All vehicles were repaired by January 15, 2024. Owner notification letters were mailed September 26, 2024. Owners may contact FCA US, LLC customer service at 1‑800‑853‑1403. FCA US, LLC's number for this recall is 77B.
Recall number 24V676000 · Recall details
Electrical system: instrument cluster/panel
- What is wrong
- Chrysler (FCA US, LLC) is recalling certain 2020-2024 Jeep Gladiator and 2018-2024 Jeep Wrangler vehicles. The instrument panel cluster may experience an internal short circuit and fail. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 101, "Controls and Displays."
- Risk
- An instrument panel that fails to display critical safety information, such as the speedometer or warning lights, can increase the risk of a crash.
- Remedy
- Dealers will replace the instrument panel cluster, free of charge. Owner notification letters were mailed between October 3, 2024, and January 23, 2025. Owners may contact FCA customer service at 1‑800‑853‑1403. FCA's number for this recall is 30B.
Recall number 24V652000 · Recall details
Power train: clutch assembly
- What is wrong
- Chrysler (FCA US, LLC) is recalling certain 2018-2023 Jeep Wrangler, and 2020-2023 Jeep Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.
- Risk
- Overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.
- Remedy
- Dealers will replace the clutch assembly and update the software, free of charge. Owner notification letters were mailed from November 16, 2023 through July 25, 2024. Owners may contact (FCA US, LLC) customer service at 1‑800‑853‑1403. FCA US LLC's number for this recall is 19A. This recall expands and replaces previous recall 21V‑028. Vehicles previously repaired under recall 21V‑028 will need to have the new remedy completed.
Recall number 23V116000 · Recall details
Power train: clutch assembly
- What is wrong
- Chrysler (FCA US, LLC) is recalling certain 2018-2021 Jeep Wrangler and 2020-2021 Jeep Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.
- Risk
- Overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.
- Remedy
- FCA US LLC will notify owners, and dealers will add software to reduce engine torque capability when clutch assembly temperatures rise to a level that may damage the inner pressure plate, free of charge." FCA has ordered a stop sale for the affected vehicles as of February 25, 2021. Owner notification letters were mailed on March 4, 2021.
Recall number 21V028000 · Recall details
Seat belts: front: retractor
- What is wrong
- Chrysler (FCA US LLC) is recalling certain 2019 Jeep Wrangler and Ram 2500, 2019-2020 Ram 1500 and 2020 Jeep Gladiator vehicles. In the event of a crash, a front seat belt retractor may not properly slow the occupant's forward movement after locking.
- Risk
- In the event of a crash, if the front seat belts fail to lock, there is an increased risk of injury.
- Remedy
- Chrysler will notify owners, and dealers will replace the front seat belt retractors, free of charge. The recall began November 12, 2020. Owners may contact Chrysler customer service at 1‑800‑853‑1403. Chrysler's number for this recall is W67.
Recall number 20V580000 · Recall details
Back over prevention: sensing system: camera
- What is wrong
- Chrysler (FCA US LLC) is recalling certain 2020 Jeep Gladiator and Jeep Cherokee, 2019-2020 Ram 1500 Pickup, Ram 2500 Pickup, Ram 3500 Pickup, Chrysler Pacifica, Dodge Durango, Jeep Grand Cherokee, Jeep Wrangler, and Jeep Renegade and 2019 Dodge Challenger vehicles equipped with 8.4" or 12" radio displays. A software error can cause the rearview camera image to remain displayed after the vehicle has been shifted out of reverse. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, "Rearview Mirrors."
- Risk
- The lingering rearview image can distract the driver, increasing the risk of a crash.
- Remedy
- Chrysler has notified owners, and dealers will update the radio display software, free of charge. Optionally, owners can choose to remotely update their software via an Over-The-Air (OTA) update available as of May 1, 2020. The recall began April 27, 2020. Owners may contact Chrysler customer service at 1‑800‑853‑1403. Chrysler's number for this recall is W30-W37.
Recall number 20V191000 · Recall details
Power train: clutch assembly
- What is wrong
- Chrysler (FCA US LLC) is recalling certain 2018-2020 Jeep Wrangler and 2020 Gladiator vehicles equipped with manual transmissions. The clutch pressure plate may overheat and fracture.
- Risk
- The overheated clutch components may increase the risk of a fire. Additionally, damage to other nearby components can result in debris falling onto the road or a loss of drive, increasing the risk of a crash.
- Remedy
- Chrysler will notify owners, and dealers will reroute a wire harness and inspect the clutch system, and replace components as needed. The recall began April 30, 2020. Owners may contact Chrysler customer service at 1‑800‑853‑1403. Chrysler's number for this recall is W12.
Recall number 20V124000 · Recall details
Steering
- What is wrong
- Chrysler (FCA US LLC) is recalling certain 2019 Jeep Wrangler and 2019 Ram 1500 vehicles. These vehicles have improperly machined steering column stub shafts that may break, possibly causing the steering wheel to detach from the steering column.
- Risk
- If the steering wheel detaches from the steering column, the driver may lose control of the vehicle, increasing the risk of crash.
- Remedy
- Chrysler will notify owners, and dealers will inspect the steering column, replacing it, as necessary, free of charge. The recall began April 5, 2019. Owners may contact FCA US customer service at 1‑800‑853‑1403. Chrysler's number for this recall is V29.
Recall number 19V201000 · Recall details
Structure: frame and members
- What is wrong
- Chrysler (FCA US LLC) is recalling certain 2018-2019 Jeep Wrangler vehicles. The front track bar brackets may be improperly welded, which can cause the bracket to separate from the frame, reducing steering capability.
- Risk
- An unexpected reduction in steering ability, can increase the risk of a crash.
- Remedy
- Chrysler will notify owners, and dealers will inspect and repair the track bar bracket welds, as necessary, free of charge. The recall is expected to begin November 17, 2018. Owners may contact Chrysler customer service at 1‑800‑853‑1403. Chrysler's number for this recall is UA5.
Recall number 18V675000 · Recall details
See all 9 recalls for the 2019 Jeep Wrangler
Defect investigations
Frame weld deficiencies
On September 16, 2019, the Office of Defects Investigation (ODI) granted Defect Petition DP18-004 and opened Preliminary Evaluation PE19-012 to investigate allegations of deficient frame welds and their potential safety related effects on 2018-2019 Jeep Wranglers. Due to a previous steering related recall that was caused by a misaligned weld on the front track bar (the federal safety agency Recall No. 18V‑675), ODI decided to include reports of steering shimmy or wobble, loose steering, and steering stiction (loss of power steering) as part of this investigation and parent petition (DP18-004). ODI received information from the vehicle manufacturer Fiat Chrysler Automobiles (FCA) via information request letters dated March 8, 2019, and February 6, 2020. Supplemental requests for information occurred between July 2020 and July 2023. A review of the responsive manufacturer information showed that vehicles presenting an unexpected reduction in steering ability due to a welding tool misalignment were correctly addressed via recall 18V‑675. General complaints concerning the weld appearance were not associated with a realized risk to motor vehicle safety. ODI identified a limited number of reports involving weld separation on vehicles that were out of scope of recall 18V‑675. FCA identified various causes of weld quality issues in early production (build dates prior to March 2018) including improper welding techniques on galvanized frames and component part variation leading to off-seam welds. These issues were addressed in production for subject vehicles built after July 2018 and preceded a drop in weld failure reports. ODI reviewed manufacturer and agency reports of weld failures out of scope of recall 18V‑675 and did not find any that resulted in a loss of vehicle control. There are no known crashes, injuries, or fatalities as a result of weld failures on vehicles not included in recall 18V‑675. Due to the steering related consequence associated with Recall 18V‑675, ODI opted to include a request for information regarding various steering issues experienced by vehicles included in this investigation. ODI reviewed manufacturer as well as agency data and determined these various steering issues were not related to any weld defect. Since the opening of this investigation, FCA has addressed the following steering concerns; a. Steering looseness due to material choice in the steering box internal components. FCA released an updated part with an internal component material less sensitive to temperature variances (TSB 08-003-21 REV. A).the federal safety agency will take further investigative action if justified. b. Steering wobble or shimmy due to a manufacturing and design deficiency in the steering damper. FCA released a part via Customer Satisfaction Notification (CSN) V41 in June 2019 which implemented supplier quality control improvements and design changes due to the presence of air in the base valve which degraded damping performance.the federal safety agency will take further investigative action if justified. c. Steering stiction, or loss of power steering, due to an underpowered steering pump calibration that occurred at highway speeds during cold weather. In December 2021, FCA released CSN Y95 which corrected this issue via software update. Due to the decreased number of consumer complaints, the service campaign appears to have addressed the issue related to an underpowered steering pump. the federal safety agency will take further investigative action if justified. The closing of this investigation does not constitute a finding by the federal safety agency that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to
PE19012
Frame Weld Deficiencies
In a letter received on October 24, 2018, a citizen petitioned the federal safety agency to initiate a safety defect investigation into frame weld deficiencies on model year (MY) 2018 'JL' Jeep Wrangler vehicles. The petitioner described a broad list of frame weld deficiencies, including porous welds, excessive slag, lack of weld penetration, over penetration of welds, overweld or weld drip, and weld splash. The weld defects are allegedly located at a variety of locations on the frame assembly.On November 16, 2018, the Office of Defects Investigation (ODI) opened a Defect Petition (DP18-004) to evaluate whether to grant or deny the petition. On March 8, 2019, ODI sent an Information Request letter to Fiat Chrysler Automobiles (FCA) requesting information on frame weld related issues on all MY 2018-2019 Jeep Wrangler 'JL' vehicles. Due to a previous steering related recall that was caused by a misaligned weld on the front track bar (the federal safety agency Recall No. 18V‑675), ODI opted to include a request for additional information concerning reports of steering shimmy or wobble, loose steering, and steering lockup in the March request letter. ODI has performed a preliminary analysis on the information obtained from FCA. Based on ODI's review of the applicable materials, the federal safety agency has decided to grant the petition. While reviewing the applicable materials obtained from the manufacturer, ODI identified various reports and references to frame welded component detachments that were outside of the scope of the federal safety agency Recall No. 18V‑675. Additionally, the information that FCA provided did not adequately address whether frame weld quality deficiencies compromise the structural integrity of vehicles, and therefore may pose an unreasonable risk to motor vehicle safety. Finally, ODI needs to further evaluate the alleged steering-related defects reported through MY 2019 and the alleged defects' relation to weld quality.The petition was granted on September 16, 2019. Preliminary Evaluation PE19-012 has been opened to further assess the scope, frequency, and potential safety-related consequences of alleged weld quality deficiencies and steering related concerns on the MY 2018-2019 'JL' Jeep Wrangler vehicles.The ODI reports cited above can be viewed on under the following reference numbers:11234967, 11222390, 11219370, 11217080, 1204905, 11179954, 11171786, 11161243, 11155523, 11153044, 11143617, 11142722, 11142426, 11141336, 11141035, 11140637, 11140344, 11140262, 11140085, 11140057, 11139880, 11139866, 11139557, 11139467, 11139436, 11138974, 11138758, 11138757, 11132030, 11129738, 11129667, 11124312, 11120232, 11119676, 11119650, 11119454, 11119450, 11115658, 11115137, 11113029, 11112515, 11110583, 11109903, 11093172, 11088501, 11076098
DP18004
Technical service bulletins for the 2019 Jeep Wrangler 837
Bulletins tell dealers how to fix known problems. A warranty extension means the manufacturer pays for that repair for longer.
2019 Jeep Wrangler fuel economy
Official EPA estimates in miles per gallon (MPGe for electric). Ranges cover trims that share the same engine.
| Engine | Drive | City | Highway | Combined |
|---|---|---|---|---|
| 2.0L 4‑cyl Hybrid | 4WD | 22-23 | 24-25 | 22-24 |
| 3.6L 6‑cyl | 4WD | 17-18 | 23-25 | 19-20 |
What 2019 Jeep Wrangler owners say
Most recent owner complaints, unedited.
The Jeep shakes uncontrollably when driving over 50 mph. A rapid braking and speed reduction to under 30 mph will stop the shaking but it will occur again and again. Stellantis has built a completely unsafe car. I can no longer drive the vehicle on the highway or with my kids in the car. I want this major safety issue repaired at the manufacturer's expense.
voltage regulator chip failure can cause the engine to stall or fail to start completely. Interior dashboard lights and dome lights along w/ windshield wipers going off without prompted happen after vehicle shutoff. Had to jump it to begin to start at times. Similar to recall U87.
Cluster panel failed. Dashboard is completely dark (ie. no speedometer, fuel guage. etc)
On [XXX], my 2019 Jeep Wrangler Unlimited Rubicon (2.0L turbo) caught fire in the engine compartment while driving, at approximately 101,437 miles. The fire started near the turbocharger and heat shield area. There were no injuries, but the vehicle was moving on a public road with four occupants, including two young children in car seats in the rear, when the fire started. The vehicle had been returned to me four days earlier, after approximately 2.5 months at Preferred Chrysler Dodge Jeep of Muskegon, MI for a timing chain replacement. After the fire, I found that the coolant reservoir hose had come off its fitting, and the hose barb appears to have been broken and the hose pushed back on. Several under-hood trim fasteners were also missing. My best assessment is that coolant sprayed onto the hot turbo/exhaust components and ignited. The vehicle has not been altered since the fire and is available for inspection at Watson's in Ludington, MI. I reported the fire to the manufacturer. They directed me to take it to the local dealer, then instructed the dealer not to inspect or work on it. The case was escalated internally, but as of 10/15/2026 no manufacturer inspection has occurred and no one has contacted me. The cause has not been confirmed by a dealer or independent shop. The fire occurred within the vehicle's Certified Pre-Owned warranty period. As of this filing, the manufacturer has not provided towing, rental, or any other assistance. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The contact owns a 2019 Jeep Wrangler. The contact stated that while driving approximately 40 MPH, the instrument panel cluster suddenly went black. The contact pulled to the side of the road and waited for a family member to follow closely behind to ensure a safe drive, as essential driving information was no longer visible. The vehicle was taken to the dealer, where it was diagnosed that the instrument panel cluster had failed and required a complete assembly replacement. The vehicle was pending repair. The contact learned of the federal safety agency Campaign Number: 24V652000 (Electrical System); however, the vehicle was not covered under the recall because the VIN was not included. The manufacturer was notified and confirmed that the VIN was not included in the recall. The failure mileage was approximately 81,000.
FCA US sent me a written warranty extension (15 years/150,000 miles) for the instrument panel cluster on my vehicle, covering a blank EVIC display with no digital speedometer, fuel level, temperature, odometer, or PRNDL. My vehicle has this condition intermittently. As I was traveling approximately 55 mph my power steering, antilock brakes, speedometer, fuel gauge, traction control, all-wheel drive, and emergency brake warning lights came on/off. I actually lost power steering and was unable to turn the vehicle off. I reached out to Jeep and advised them of this and that I received the letter for the instrument panel cluster XZ1 and I thought this was related. I read the letter to them word for word, and they had the dealership perform the recall on my clutch. I didn't know until all of the same things happened again and I checked the receipt to confirm the work performed. I reached out to Jeep the same day and that was more than a week ago. I now have a new service transmission light. My vehicle is not safe to drive and they still don't even know why I called. My case number with Jeep is 98166358.
The contact owns a 2019 Jeep Wrangler. The contact stated that while driving approximately 45-50 MPH northbound on the Hutchinson River Parkway, the steering wheel failed to operate as needed. The vehicle was uncontrollable and started drifting towards the left before crashing into the highway barrier. The message “Electronic Driver Assist” was displayed. The vehicle was towed to the body shop. The manufacturer was contacted by phone, and the contact spoke with a customer representative, and a case was opened. The contact was informed that the investigating team would reach out in 2 to 4 days. An inspector had been assigned by Geico Insurance Company. The approximate failure mileage was 59,000.
The 48-Volt Lithium-Ion eTorque Hybrid Battery Pack (Mopar Power Pack Unit/PPU) on my 2019 Jeep Wrangler Sahara Unlimited (~55K miles) failed. The failed component may be available on video by the dealership. Check engine light first appeared early XXX. Earliest dealership appointment was late August 2026. At that visit, dealer diagnosed DTCs P0A94 (recurring, including P0A94-03) and U0412, and performed a software update flashing the BPCM (Battery Pack Control Module) firmware from 05057870AN to 05057870AV per a Technical Service Bulletin. This was covered under warranty at no charge; vehicle was returned to me. Days later, the check engine light returned along with a battery warning light and additional indicators, including ABS among others I could not fully identify. The vehicle then lost power and stopped running while in the roadway, disabled in an active lane of travel — a safety hazard to myself and surrounding traffic. Vehicle was towed to the dealership XXX. On this second visit, the dealership attributed the failure to moisture exposure and corrosion at the PPU connector/harness, denied warranty coverage, and charged me $4,561.90. I received the repaired vehicle XXX. I opened a case with Stellantis Customer Care (Case #XXX) with case manager [XXX] to request a technical review of the failure and the warranty denial. [XXX] stated he contacted the dealership five times seeking information or resolution and received no response. He offered rental car reimbursement up to $50/day during the repair. Dealership diagnosed and repaired the vehicle on both occasions. No known inspection by manufacturer, police, or insurance beyond the review requested under Stellantis case #XXX. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
My 2019 Jeep Wrangler has experienced a failure of the Blind Spot Monitoring system. The vehicle repeatedly displays a “Blind Spot Alert Temporarily Unavailable” warning, causing the blind spot detection system to become unavailable while driving. The vehicle was inspected and diagnosed by an authorized Jeep dealership. Diagnostic trouble codes were present, and I was advised that Stellantis has issued a service bulletin addressing this condition and that the diagnostic codes indicate replacement of the mirror glass/components associated with the blind spot monitoring system. This concerns me because the system is an important safety feature designed to alert the driver to vehicles located in areas that may not be visible in the mirrors. When the system fails, those warnings are unavailable. Despite this being a documented issue addressed by a manufacturer service bulletin, I was informed that there is currently no recall and that the necessary mirror replacement is not covered under my extended warranty. I am filing this complaint because I believe a recurring failure involving a vehicle safety system should be documented and investigated to determine whether other Jeep Wrangler owners are experiencing the same problem and whether further manufacturer action is warranted.
Compare the 2019 Jeep Wrangler
Wrangler vs Toyota 4RUNNERWrangler vs Ford Bronco
Other model years
1990199119921993199419951996199719981999200020012002200320042005200620072008200920102011201220132014201520162017201820192020202120222023202420252026
Questions about the 2019 Jeep Wrangler
Is the 2019 Jeep Wrangler reliable?
Owners have filed 749 complaints about the 2019 Jeep Wrangler, 1.3 times a typical Wrangler model year.
What is the 2019 Jeep Wrangler year score?
The 2019 Jeep Wrangler scores 58 out of 100 (below average). The score compares it with the other model years of the Jeep Wrangler: 75 is a typical year, 50 means twice the usual complaints, and serious complaints and recalls lower it.
What is the most common problem with the 2019 Jeep Wrangler?
Steering, with 448 complaints, typically around 2,300 miles. Next is electrical (153).
How many recalls does the 2019 Jeep Wrangler have?
9 recalls, covering back over prevention, electrical system and power train.
Was there a recall on the 2019 Jeep Wrangler steering?
Yes, 1 recall: 19V201000. Check your VIN to see if your car still needs the free repair.
What year does the Jeep Wrangler have bad steering?
The Jeep Wrangler model years with the most steering complaints are 2018 (1,117 complaints), 2019 (448 complaints) and 2021 (255 complaints).
What gas mileage does the 2019 Jeep Wrangler get?
Official estimates for the 2019 Jeep Wrangler range from 19 to 24 mpg combined. The most efficient version (2.0L 4-cyl hybrid, 4WD) gets 22-23 city and 24-25 highway.
VIN decoder
See the problems and recalls for an exact car
Buying a used 2019 Jeep Wrangler?
Check the exact car before you pay: accidents, salvage or flood titles, odometer readings and previous owners.
Check its historyJeep Wrangler in the news
- Jeep recalls 2026 Grand Cherokee, 2026 Wrangler and 2026 Cherokee and other models over back over prevention camera problem (844,028 vehicles)
- Jeep extends warranty coverage on 2018-2023 Wrangler, 2020-2023 Gladiator and 2021-2023 Wrangler 4xe (structure body)
- Jeep extends warranty coverage on 2018-2022 Wrangler, 2020-2022 Gladiator and 2021-2022 Wrangler 4xe (electrical system)